5. 2 Cautions on Connection

¥When connecting the camera cables, be sure to turn off the camera control unit and any other equipment connected to it.

¥For DC power supply connecting to DC IN 12V terminal, use class II DC power supply approved according to EN60950-1 in Europe. or use UL listed and/or CSA approved ungrounded type AC adaptor with the speciÞcations described below in U.S.A. or Canada.

Power supply voltage

: 12V DC ±10%

Current rating

: More than 1.5A

Ripple voltage

: Less than 50 mV (pÐp)

Connector

: HR10AÐ7PÐ4S by HIROSE electronics Co. Ltd

 

Pins 1, 2

: 12V

 

Pins 3, 4

: GND

¥If the securing screw on the connector of the camera cable loosens, noise may appear on the screen. Be sure to tighten the connector completely.

¥Only use the speciÞc optional camera heads with this camera controller.

The use of any other camera heads may cause damage to the control unit and camera head.

¥The video signal output of this camera control unit has no function for automatically selecting output according to the monitor TV. Therefore, be sure to switch the output mode of this camera control unit according to the monitor as no image will be displayed on the monitor if the camera output mode and the monitor input mode do not match. For switching, refer to the item 6.6 ÒSwitching of Video Signal OutputÓ.

5. 3 Connector Pin Assignments

The rear panel of the camera control unit has the following connectors:

DC IN 12V; SYNC IN/OUT; 3G/HD-SDI; REMOTE and DVI-D terminal. Use the appropriate cables to connect with these connectors.

DC IN 12V KEY LOCK

FORMAT

SYNC

SYNC IN/OUT

 

 

 

 

3G/HD-SDI

1

4

ON

 

50

IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

3

OFF

 

59.94

OUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

REMOTE

 

 

 

 

 

 

DVI-D

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

2

3

4

5

 

1

2

3

4

5

6

7

8

 

6

 

7

8

9

 

9 10 11 12 13 14 15 16

 

 

 

17 18 19 20 21 22 23 24

DC IN 12V terminal

 

REMOTE terminal

 

DVI-D terminal

 

 

1

+12V

 

1

NC

 

1

Data2-

13

NC

2

+12V

 

2

TXD

 

2

Data2+

14

+5V

3

GND

 

3

RXD

 

3

Data2 Shield (GND)

15

GND

4

GND

 

4

NC

 

4

NC

16

Hot Plug Detect

 

 

 

5

GND

 

5

NC

17

Data0-

 

 

 

6

NC

 

6

NC

18

Data0+

 

 

 

7

NC

 

7

NC

19

Data0 Shield (GND)

 

 

 

8

NC

 

8

NC

20

NC

 

 

 

9

NC

 

9

Data1-

21

NC

 

 

 

 

 

 

10

Data1+

22

Clock Shield (GND)

 

 

 

 

 

 

11

Data1 Shield (GND)

23

Clock+

 

 

 

 

 

 

12

NC

24

Clock-

11