Toshiba RAV-SM562AT-E FILE NO. SVM-06012, No display in the setting at shipment, Check, code

								FILE NO. SVM-06012
			Table 9-2-2
	Operation of diagnostic function
								Judgement and action
Block	Check		Symptom	Unit	Condition
	code			status
[MODE]		The serial signal is not output		Operation	Displayed when	1.	Outdoor unit does not completely
[TIMER] lamp		from outdoor unit to indoor unit.		continues.	error is detected		operate.
5Hz flash		•	Miscabling of inter-unit cables				•	Inter-unit cable check, correction of
		•	Defective serial sending circuit				•	miscabling
		•	on outdoor P.C. board					Outdoor P.C. board check, P.C. board
			Defective serial receiving circuit				•	cables check
		•	on outdoor P.C. board					Compressor case thermo check
			Compressor case thermo			2.	In normal operation
			operation				When outdoor sending serial LED
							(Green) flashes, the receiving serial
							LED (Orange) also flashes. : Indoor
							P.C. board (Main P.C. board) check
							When the receiving serial LED (Orange)
							does not flash: Outdoor P.C. board
							check
		BUS communication circuit error		Operation	Displayed when	1.	Communication line check, miscabling
		* BUS communication was		continues	error is detected		check
			interrupted over the specified	(According			Power supply check for central control
			time.	to remote			(Central control remote control, etc.)
				control of			and indoor unit
				indoor		2.	Communication check (XY terminal)
				unit)		3.	Indoor P.C. board check
						4.	Central control check
							(Communication P.C. board)
		Error in 4-way valve system		Operation	Displayed when	1.	Check 4-way valve.
		•	Indoor heat exchanger	continues.	error is detected	2.	Check 2-way valve and non-return
			temperature rise after start of				valve.
		•	cooling operation.			3.	Check indoor heat exchanger sensor
			Indoor heat exchanger				(TC).
			temperature fall after start of			4.	Check indoor P.C. board
			heating operation.				(Main P.C. board).
		Error in other cycles		Operation	Displayed when	1.	Compressor case thermo operation.
		•	Indoor heat exchanger temp	continues.	error is detected	2.	Coming-off of detection part of indoor
			(TC) does not vary after start of				heat exchanger sensor.
	*		cooling/ heating operation.			3.	Check indoor heat exchanger sensor
						4.	(TC).
							Check indoor P.C. board
							(Main P.C. board).
[MODE] lamp		Coming-off, disconnection or		Operation	Displayed when	1.	Check indoor temp sensor (TA).
5Hz flash		short of indoor temp sensor (TA)		continues.	error is detected	2.	Check indoor P.C. board
							(Main P.C. board).
		Coming-off, disconnection or		Operation	Displayed when	1.	Check indoor temp sensor (TC).
		short of indoor temp sensor (TC)		continues.	error is detected	2.	Check indoor P.C. board
							(Main P.C. board).
		Coming-off, disconnection or		Operation	Displayed when	1.	Check indoor temp sensor (TCJ).
		short of indoor temp sensor		continues.	error is detected	2.	Check indoor P.C. board (Main P.C.
		(TCJ)					board).
[MODE] lamp		Error in indoor fan system		All stop	Displayed when	1.	Check indoor fan motor connector
5Hz flash		Revolutions frequency error of fan			error is detected		circuit (CN210).
						2.	Check indoor fan.
						3.	Check indoor P.C. board
							(Main P.C. board).
		Error in indoor unit or other		Operation	Displayed when	1.	Check indoor P.C. board
		positions		continues.	error is detected		(EEPROM and peripheral circuits)
		1. EEPROM access error					(Main P.C. board).
		Outside error input		Operation	Displayed when	1.	Check outside devices.
		Detected by input voltage level		continues.	error is detected	2.	Check indoor P.C. board
		from outside devices					(Main P.C. board).
		Outside interlock input		All stop	Displayed when
		Detected by input voltage level			error is detected
		from outside devices

*: No display in the setting at shipment

– 24 –