PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 39
FLEXIBLE BUTTON ASSIGNMENT REFERENCE GUIDE
~-~~~~-~~~~-~-~~~~-~-~
SELECT = Port Number T Code: 1 or range. See Note 4. Press LED/button Enter the appropriate code that corresponds to be defined. See tables to the feature to be assigned. See the on the following pages. feature code reference table below.
Momentarily unlocks door
(3 or 6 sec.). See Prog. 77-l
77
89
Resets alarm
condition system wide
Alarm Reset
or ALRM
All Call Page
or AC
\larm
411 Call
loice Page
4utomatic
3usy Redial
4utomatic
:allback Bus\
Pages all idle electronic/digital
telephones over speaker
Sets ABR of busy outgoing
number
Sets ACB for station
recalled by busy line
Turns BGM ON or OFF
through station speaker
Auto Busy Redial
3ackground
Vlusic
>all Forward Call Frwd All Calls All calls forward to selected
411 Calls or CFAC 87 station
3all Forward
4.C. Fixed Call Frwd to:
or CFF 86 Forwards all calls to pre-defined
destination. See Prog. 36
Zall Forward
3usy Call Frwd Busy
or CFB Forwards calls to selected 5g station if station is busy
Zall Forward
3usylNo
4nswer
Call Ftwd Busy/
NAns
or CFBINA 57 Forwards calls to selected
station if station is busy or
does not answer
Zall Forward Call Frwd
No Answer No Answer 58 Forwards calls to selected
or CFNA I I station if station does not answer

r

Picks up ringing or held intercom.
Call Pickup
Tenant 1 1 rn”r’ 83 Picks up tenant 1
ringing CO calls Privacy Release
Redial Last
Number (# key)
Privacy Release 7g
or PRV RLS
RDL
(EKT only) ”
Changes station Privacy
mode to Non-private for CO?
Redials the last
number
Release Release Call
or RLS 76 Releases current call
and makes station idle
Save Last Save Last Number 85 Saves last number dialed
Number or SAVE for future speed dial
Speed Dial Speed Dial 97 Begins speed dial
Select (* key) or SDS selection
PKUPP 82 Picks up tenant 2
rinaina CO calls
Call Pickup
Tenant 2
CO Line
Appearance 1 - 08 CO line access of
appearing calls
Line 01 - 08
or CO 01 -
CO 08
30 Not I Do Not Disturb
3isturb or DND I I
g8 Prevents calls to station
I
Door Lock 0 Unlock Door 0
or DRLK 0 7, Momentarily unlocks door
(3 or 6 sec.) PIOUS/PIOU
II.,
NOTES:
1. For more information, see instructions preceding record sheets.
2. Complete Program 38 before Program 39.
3. initialized data assigns the keystrip pattern associated wfth Gode 31 worn Program 38.
4. Specify a range of ports by keying in:

q omnn

Low port-’ L High port
5. Flash (FLASH) (MW/FL): Sets pauses in Speed Dial if telephone does not have a pause button. Sets f/ashes in Speed Dial numbers if telephone has a
pause butfon.
6. Redial (MEDIAL or RDL) and Speed Dial (SDS): Both buttons must be programmed on Electronic telephones; not allowed separately. Recommended
on all stations using voice mail, since they allow easy access of * and # DTMF buttons (see note 8 below).
7. Pooled Line Grp (PL): Codes 67 - 68 represent CO line groups 81 - 88. Maximum four Pooled Line Grp (PL) buttons perpooled line group on each
station.
8. Redial is a fixed button on 2000-series Digital Telephones andREDIAL is a fixed button on IOCJO-series Digital telephones. Do not assign button as flexible
button on digital felephones; a/so, Speed Dial (SDS) is initialized on flexible button 20 on Digital telephones.
2-76