IMPORTANT SAFETY INSTRUCTIONS (Continued)
POWER SUPPLY INFORMATION
20.If glass components, including lens and lamp, should break, contact your
dealer for repair service.
This product incorporates glass components, including a lens and a lamp.
If such parts should break, please handle with care to avoid injury and contact your dealer for repair service. Avoid any broken pieces of glass since they may cause injury. In the unlikely event that the lamp ruptures, thoroughly clean the area around the projector and discard any edible items placed in that area since they may be contaminated.
21. Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
23. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to verify that the product is in proper operating condition.
24.Do not leave thermal- paper documents or easily deformed items on top
of the unit or near the air exhaust for long periods of
time.
The heat from the unit could erase the information on the thermal paper, or cause deformation or warping.
If your line voltage is 220 to 240 V, use one of the following types of cable/plug. | Using | |||
Plug |
| Plug |
| |
configuration Plug type | Line voltage | configuration Plug type | Line voltage |
|
EURO | 0 – 40 V | Australian | 00 – 40 V | Before |
40 V |
| |||
|
|
| ||
|
| 10 A |
| |
|
|
|
| |
UK | 0 – 40 V | Switzerland | 00 – 40 V |
|
40 V |
|
| ||
|
| 6 A |
|
|
Use a 5 A fuse which is approved by | North American 00 – 40 V | |
ASTA or BSI to BSI6. | ||
40 V | ||
Always replace the fuse cover after | ||
15 A | ||
changing the fuse. | ||
|
IMPORTANT PRECAUTIONS
Moisture Condensation
Never operate this unit immediately after moving it from a cold location to a warm location. When the unit is exposed to such a change in temperature, moisture may condense on the lens and the crucial internal parts. Do not use the unit for at least 2 hours when there is an extreme or sudden change in temperature to prevent the unit from possible damage.
Place and Manner of Installation
• Do not place in hot locations, such as near heating equipment. Doing so could cause |
22. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other hazards.
(Only the replacement of the lamp should be made by users.)
25.Do not use the product in a closed installation
location.
Do not place the product in a box or in any other closed installation location. Otherwise it may overheat, which could result in a risk of fire.
26.Do not look into the laser light source of the remote control or direct the laser pointer toward a person or
a mirror.
The laser beam may cause damage to the eyesight.
malfunction, and shorten the life of the projector. |
• Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts, shortening |
their lives, and darkening the screen. |
• Do not use this product in the upright position or tilt it up or down by more than 20° from |
level. Doing so may cause a failure or shorten the life of the product. |
• Using this instrument near a TV or radio may cause interference to the images or audio |
sound. If this happens, move it away from the TV or radio. |
• Moving the projector from a |
condensation on the lens or internal parts. If you continue to use it in that situation, it may |
malfunction. Wait until the condensation naturally disappears. |
• In a high altitude location where air is thin, cooling efficiency is reduced so use the |
projector with [Fan mode] set to [High]. p.42 |
• Only plug the power cord into outlets rated for use with the power cord’s specified voltage |
range. Do not overload extension cords or power strips as this can result in fire or electric |
shock. |
• Route the power cable or the connecting cable away from where people could trip over it. |
The projector may fall down, which could result in severe injury. |
• Be sure the power cord is easily reached for unplugging in case of emergency. Do not |
place any obstacles near a wall outlet in which the cord is plugged. |
