Toshiba TLF-XD2000 owner manual Connection, Placement Styles, Before connection

a (max length) = projection size (inches) – 0.7244 27.248

a (min length) = projection size (inches) – 0.8786 32.773

Placement

Placement Styles

As shown in the figures below, this device can be placed in 4 different styles.

The factory setting is “floor-mounted front projection.” Set the [Projection mode] in the Default setting 2 menu, in accordance with your needs. p.41

Connection

Before connection

•	Read the owner’s manual of the device you are connecting to the projector.
• Some types of computer cannot be used or connected to this projector.
	Check for an RGB output terminal, supported signal p.51 , etc.

Floor-mounted front projection

•	Turn off the power of both devices before connecting.
• The figure is a sample connection. This does not mean that all of these devices can or
	must be connected simultaneously. (Dotted lines mean items can be exchanged.)

Computer	Video recorder,	Computer	Computer
(for control)
	DVD player, etc.

To RS-232C terminal

	To audio output	To S-video output
	White (L)/Red (R)
	Audio cable	S-video cable
p.53	(not supplied)	(not supplied)

To audio output

To audio

output

To RGB

output Audio cable

To RGB output

Preparations

Ceiling-mounted rear projection

Control cable

Audio cable (not supplied)

(not supplied) RGB cable (supplied)

RGB cable (not supplied)

WARNING

•Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit. Attempting to clean/replace the lamp at a high site by yourself may cause you to drop down, thus resulting in injury.

•If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting the projector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge. Improper mounting could cause the projector to fall, resulting in an accident.

•If the projector is ceiling-mounted, install the breaker for turning off the power in case of anomaly. Let everyone involved with the use of the projector know that fact.

Monitor

It is necessary to switch to MONITOR OUT by the switch.

Projection Distance and Size

Use the figures, tables, and formulas below to determine the projection size and projection distance. (Projection sizes are approximate values for full-size picture with no keystone adjustment.)

AV cable

(not supplied)

Audio cable (not supplied)

Audio cable (not supplied)

p.18

Monitor cable Mini D-sub 15P-BNC (not supplied)

To Y/CB/CR output Green (Y)/Blue

(CB)/Red (CR)

Screen As seen from above

90°

To audio
output	To video
White (L)/
Red (R)	output

To audio input White (L)/Red (R)

To audio output

Conversion adapter BNC-pin (not supplied)

As seen from the side

Lens center

90°

H

a

a is the distance (m) between the lens and the screen, and corresponds to a range of 1.19 m to 9.13 m. H is the height from the image bottom to the center of the lens.

projection		projection distance a (m)		height (H)
size (cm)		min length	max length	(cm)
		(zooming max)	(zooming min)
33 (84)		–	1.19	6.0
40	(102)	1.19	1.44	7.3
60	(152)	1.80	2.18	10.9
80	(203)	2.41	2.91	14.5
100	(254)	3.02	3.64	18.1
150	(381)	4.55	5.48	27.2
200	(508)	6.08	7.31	36.3
250	(635)	7.60	9.15	45.4
300	(762)	9.13	–	54.4

Video recorder, etc. Audio amplifier, etc. DVD video recorder, etc.

20 21