Basic operations
1Turn on the power.
Turn on the power by following the instructions in “Turning on the power” p.20 .
2Select the language and the lamp power (When using the first time).
When the projector is used for the first time after purchase, menu for language and lamp power selection and configuration is displayed in English. (If the screen is out of focus, adjust it according to the step 6 .)
5Projector placement angle adjustments
The placement angle and the height of the projected image can be adjusted by the foot adjuster.
q Lift up the front of the projector to | 1 |
the desired angle, then press the |
|
foot adjuster release button. |
|
The foot adjuster extends. Release the |
|
button to lock the position. |
|
qUse the 
or 
buttons to select the desired language and press the 
button.
Message for setup confirmation is displayed in a selected language.
wUsing the 
or 
button, select Standard or Low and press the 
button.
The lamp power, if selected, will be toggled without pressing the 
button. The display automatically disappears in a few seconds.
English ................ English
Français .............. French
Deutsch .............. German
Italiano ................ Italian
Español ............... Spanish
Português .......... Portuguese
................... Japanese
....... Chinese (simplified)
....... Chinese (traditional)
................... Korean
w Turn the foot adjuster to |
| 2 | |
the angle. | 3 | ||
|
eTo adjust the horizontal angle, use the tilt adjuster.
To stow the foot adjuster, hold up the projector while pressing the foot adjuster release button, then slowly lower the projector.
6 Adjust the picture size and focus.
qMove the projector back and forth to adjust
Notes
•When the projector is turned on the next time, the Language and Lamp power menus do not appear upon startup. However, if “Reset all” is executed from the Reset menu p.31 , the Language and Lamp power menus will be displayed the next time when the power is turned on
•The language can also be set via the Display setting menu p.30 and Lamp power via the Default setting menu p.30 .
•This owner’s manual assumes that English has been selected.
3Place connected device(s) in operating status.
Turn on and boot up connected computers and other devices.
the screen size.
w Use the focusing ring to adjust the focus.
7Adjusting the volume with the 
buttons
The speaker volume can be adjusted when an audio signal is being input.
Notes
• | Note that because of the lamp characteristics, the brightness of the lamp may fluctuate slightly. |
• | A lamp is a consumable supply. |
| If used for extended periods, images will appear dark, and the lamp could burn out. This |
| is characteristic of a lamp, and is not malfunction. (The lifetime of the lamp depends on |
| conditions of use.) |
Operations
4Select input.
qPress the INPUT button.
A list of inputs appears on the screen.
wUse the 
buttons to select the desired input, and press the 
button.
The picture for the selected input is projected.
Computer
Y/PB/PR
Video
• | The LCD panel is made using extremely advanced technology, but there may be black | ||
| spots (pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. | ||
| Please note that these are not malfunctions. |
|
|
• | Although this projector supports a wide range of RGB signals p.38 , any resolutions not | ||
| supported by the model (XGA or SVGA, depending on the model) will expand or shrink the | ||
| pictures, and will affect image quality slightly. To view | ||
| recommended that the computer’s external output should be set to the projector’s resolution. | ||
• | With some models of computer having LCD displays or the like, displaying images | ||
| simultaneously on the projector and the monitor’s display may cause the images to be | ||
| shown improperly. If this happens, turn off the computer’s LCD display. For information on | ||
| how to turn off the LCD display, see the owner’s manual of your computer. | ||
• | If a signal not supported by the projector is input, the | icon will appear. | |
• | If a no signal is being input from the connected device, the | icon will appear. | |
• | If an unavailable operation button is pressed, the | icon will appear. | |
22 | 23 |
