Storing Channels on the VCR (continued)
Adding channels
If a desired channel cannot be scanned automatically because of a weak signal, it can be added to the memory.
Erasing channels
You can erase a stored channel from the memory if it is unnecessary.
1)Follow steps 1 to 3 of “Incoming Antenna/CATV Signals”.
2)Select “ADD CH” or “ERASE CH” usingPLAY/X2 or STOP.
To add channels |
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
| PROGRAM |
| SET UP |
|
|
| PRESET |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| TV |
| CATV |
| ||
|
|
|
| TV / CATV |
|
|
| ||||||
|
|
|
|
|
|
|
| OFF |
| On |
| ||
AUTO SCAn |
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ADD CH |
|
|
|
|
| – |
| ||
|
|
|
| ERASE CH |
|
|
|
|
| – |
| ||
|
|
|
| TO SET CH |
|
|
| ||||||
|
|
|
| PUSH 0~9 KEYS |
| ||||||||
|
|
| EnD: PROG |
|
|
|
|
|
|
|
| ||
To erase channels |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
| PROGRAM |
| SET UP |
|
|
| PRESET |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| TV / CATV |
|
| TV |
| CATV |
| |||
|
|
| AUTO SCAn |
|
| OFF |
| On |
| ||||
|
|
|
| ADD CH |
|
|
|
|
| – |
| ||
|
|
|
| ERASE CH |
|
|
|
|
| – |
| ||
|
|
|
| TO SET CH |
|
|
| ||||||
|
|
|
| PUSH 0~9 KEYS |
| ||||||||
|
|
| EnD: PROG |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3)Enter a channel number of 1 to 125 using number buttons.
For more than 100 number, first press 100. For CATV channels, refer to the chart below. (For other orders, check with your cable company.)
4)Repeat steps 2) and 3) to add or erase channels as necessary.
5)Press PROG. to exit.
To set the Cable Box/DSS output Channel on the VCR.
1)Press PROG. to display the MENU screen.
2)Select “PRESET” usingFF or REW, and press
ENTER.
3)Select “CABLE BOX/DSS” usingPLAY/X2 or STOP, and press ENTER.
PROGRAM SET UP PRESET
USEnO C . BOX DSS
EnD: PROG
4)Select “NO”, “C.BOX” or “DSS” usingFF or REW according to your connection type.
5)If set to “C.BOX” or “DSS”, select “OUTPUT CH” using PLAY/X2 or STOP. Then enter the output channel number of your cable box (Usually 3 or
4, check the rear of the cable box.) or line input mode “L1” using theI.SELECT button according to your connection.
PROGRAM SET UP PRESET
USEnO C . BOX DSS
OUTPUT CH3 CH
TO SET CH
PUSH 0~9 KEYS
EnD: PROG
6)Press PROG. to exit.
Once the active channels have been stored, you can select the channels in two ways below.
Number buttons
To enter digits of the channel number.
•For
•For more than 100 number, first press 100.
•Each number button needs to be pressed within 2 seconds.
CH/TRK
To shift up or down the stored channel numbers.
1 8