Load Balance Broadband Router User Guide, Total | TP-Link TL-R480T+

Image 87

TP-Link TL-R480T+ manual Load Balance Broadband Router User Guide, IP Address, MAC Address, Total, Packets, Bytes, Current

Contents

Rev 4.1.0 TL-R480T+ Load Balance Broadband Router All rights reserved COPYRIGHT & TRADEMARKS CE Mark Warning FCC STATEMENT Package Contents Conventionsor missing, please contact with your distributor Chapter Hardware installationChapter 3. Quick Installation Guide Chapter 1. Introduction Appendix D Glossary Appendix A SpecificationsAppendix C FAQ Appendix B Preventing Lightning TL-R480T+ 1.2 FeaturesChapter 1.Introduction 1.1 Overview of the Router 1.3 Conventions Status Chapter 2.Hardware installation2.1 Panel Layout 2.1.1 The Front Panel Ensure the router is powered on before it restarts completely 2.1.2 The Rear Panel Connecting to the Grounding Bar 2.3 Installation Environment Requirements2.2 System Requirements 2.4 Connect to Ground Connecting to the Ground via the power supply 2.5 Connecting the Router Load Balance Broadband Router User Guide 3.1 Configure PC Chapter 3.Quick Installation Guide Load Balance Broadband Router User Guide Step 4 Configure the IP address as shown in Figure 3-4. After that, click OK 3.2 Login 2 Is the TCP/IP configuration for your PC correct?1 Is the connection between your PC and the Router correct? Step 1 Select the Quick Setup tab on the left of the main menu and the “Quick Setup” screen will appear. Click the Next button Step 3 If you choose PPPoE, you will see the screen as shown in Figure 3-10. Enter the Username and Password provided by your ISP. These fields are case sensitive. If you have difficulty with this process, please contact your ISP 4.1 Status Chapter 4.Configuring the Router ¾ LAN - This field displays the current information for the LAN, including the “MAC address”, “IP address” and “Subnet Mask” Please refer to chapter 3Quick Installation Guide 4.2 Quick Setup4.3 Network 4.3.1 WAN/LAN Number 1 By default, TL-R480T+ is set to work at the mode of dual WAN ports 4.3.2 LAN 1. Dynamic IP 4.3.3 WAN ¾ WAN Port Here allows you to select the WAN port to configure 2. Static IP 3. PPPoE ¾ Connect on Demand - You can configure the router to disconnect your Internet connection after a specified period of inactivity Max Idle Time. If your Internet connection has been terminated due to inactivity, Connect on Demand enables the router to automatically re-establish your connection as soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, check the radio button and click Save to apply ¾ Connect Automatically - Connect automatically after the router is disconnected. To use this option, click the radio button 4. BigPondCable ¾ Ingress Bandwidth Enter the bandwidth for download traffic Load Balance Broadband Router User Guide 5. L2TP Load Balance Broadband Router User Guide 6. PPTP Load Balance Broadband Router User Guide 4.3.4 Network Service Detection 4.3.5 MAC Clone 4.3.6 Load Balance2 Only the PCs on your LAN can use the MAC Address Clone feature ¾ Enable/Disable WAN - Click the check box of WAN which you want to enable the Load Balance Bytes Tx + Rx - Bytes transmitted and received through the WAN port How to set an extra IP address dispatch rule? Step 1 Click Add New… button, you will see the following screen 4.3.7 Balance PolicyStep 3 Click Save to apply your setting To add a dispatch rule 4.3.8 WAN Port Parameter 4.4 DHCP 4.4.1 DHCP Settings 4.4.3 Address Reservation 4.4.2 DHCP Clients List To add/modify a reserved IP address 4.5 Forwarding2 The function wont take effect until the router reboots Other configurations for the entries as shown in Figure To add/modify a virtual server entry 4.5.1 Virtual Servers 4.5.2 Port Triggering To add/modify a port triggering entry ¾ Trigger Port - This displays the port for outgoing traffic. An outgoing connection using this port will Trigger this rule 4 Incoming Port Range cannot overlap each other 4.5.3 DMZ To assign a computer or server to be a DMZ server 4.5.4 UPnP 4.5.5 ALG 4.6 Security 4.6.1 Firewall 4.6.2 IP Filtering Step 6 Click the Save button to save this entry To add/modify an IP Address filtering entry 4.6.3 Domain Filtering To add or modify a Domain Filtering entry To add or modify a MAC Filtering entry 4.6.4 MAC Filtering 4.6.5 Screen ¾ Scan Attack Defence ¾ Region - This option used to select the specifically area from which the packets will be monitored by the next settings IP address ten different ports, then the source IP address will be deemed to make Port Attacks. And the Router will start up the blocking function immediately ¾ DoS Attack Defence¾ Dubious Packet Defence ¾ Packet Defence with IP option 4.7 Static Routing To add/modify a static routing entry 4.8 Session Limit 4.8.1 Session LimitTo add/modify a session limit entry 4.9 QoS 4.8.2 Session ListYou can click the Refresh to update the information 4.9.2 QoS Rules List 4.9.1 QoS Settings To add/modify a QoS rule 4.10.1 Binding Setting4.10 IP & MAC Binding Setting, ARP List To add/modify an IP & MAC binding entry Step 2 Enter the MAC Address and IP Address in the corresponding fieldTo find a specific IP & MAC binding entry You can click “to page” to edit the entry in the corresponding screen 4.10.2 ARP List 4.11.1 Dyndns DDNS 4.11 Dynamic DNS To set up for Dyndns DDNS, follow these instructions 4.11.2 PeanutHull DDNS To set up for PeanutHull DDNS, follow these instructions 4.11.3 Comexe DDNS To set up for Comexe DDNS, follow these instructions 4.11.4 No-IP DDNS To set up for No-IP DDNS, follow these instructions 4.12 Switch Settings 4.12.2 Port Mirror 4.12.1 Port Statistics 4.12.4 Port Parameter 4.12.3 Port Rate Control 4.12.5 Port Status 4.12.6 Port VLAN 4.13 System Tools 4.13.1 Time Settings To configure the system time manuallyTo configure the system automatically 2 The time will be lost if the router is turned off 4.13.2 Diagnostic Tools 1. Only one user can use these tools at one time 4.13.3 FirmwareTo upgrade the routers firmware, follow these instructions below 4 The router will reboot after the upgrading has been finished 3 The default IP Address is 4 The default Subnet Mask is 4.13.4 Factory Defaults4.13.5 Backup and Restore 1 The default User Name is admin 2 The default Password is admin To restore the Router’s settings Step 2 Click the Restore button to completeStep 2 Save the file as the appointed file shown in Figure 2 MAC Clone system will reboot automatically 3 DHCP service function 4.13.6 Reboot4.13.7 Password 1 Change LAN IP Address. System will reboot automatically 4.13.8 System Log 4.13.9 Remote Management3 You can click the Clean All button to clean all the configurations 4.13.10 Statistics Packets IP AddressMAC Address Total 4.13.11 IP NAT Table 4.13.12 NAT Source Port Settings Appendix A Specifications GeneralPhysical and Environment Appendix B Preventing Lightning 1. How do I configure the router to access Internet by ADSL users? Appendix C FAQ Method one Use Virtual Server TL-R480T+ Load Balance Broadband Router User GuideSave 3. I want to use Netmeeting, what do I need to do? Figure C-4 Method two Use DMZ Host7. I want to build a WEB Server on the LAN, what should I do? Figure C-7 Figure C-6 Appendix D Glossary