¾ Click on the WPA Encryption Setting button | TP-Link TL-WN322G

¾Click on the WPA Encryption Setting button.

TL-WN322G54M Wireless USB Adapter User Guide

Figure 4-7 More settings—TKIP

¾Authentication: Select WPA from the drop-down list.

¾Encryption: Select TKIP or AES from the drop-down list.

¾Click on the WPA Encryption Setting button.

In this section you can configure the settings for TLS or PEAP. TLS (Transport Layer Security) is an IETF standardized authentication protocol that uses PKI (Public Key Infrastructure) certificate-based authentication of both the client and authentication server.

- 18 -

Image 23

TP-Link manual ¾ Click on the WPA Encryption Setting button, TL-WN322G 54M Wireless USB Adapter User Guide

Contents

Page All rights reserved COPYRIGHT & TRADEMARKS CE Declaration of Conformity FCC STATEMENTFCC RF Radiation Exposure Statement IMPORTANT NOTE FCC Radiation Exposure Statement ¾ EN 301 489-1 V.1.4.1 2002 / EN 301 489-17 V.1.2.1 ¾ EN 60950-1 ¾ EN 300 328 V.1.4.1 Chapter y Drivers and Utility Package ContentsTL-WN322G 54M Wireless USB Adapter User Guide 1.2 LED Status 1.1 FeaturesLED Indicator Chapter 1 Introduction Infrastructure Mode 1.4 Network ConfigurationAd-hoc peer-to-peer Mode Figure 1-2 Infrastructure mode 2.1 Before You Begin Chapter 2 Installation Guide2.2 Installing the Drivers ¾ Wait a few moments until the files are copied to the computer Figure 2-2 Install Shield-Choose Destination LocationFigure 2-3 Install Shield-Setup Status Figure 2-4 Installation Complete 3.1 Through Control Panel Chapter 3 Uninstall Guide1. Click on Start Settings Control Panel Add or Remove Programs 3.2 Through Programs TL-WN322G Wireless Utility Figure 3-6 Uninstalling TL-WN322G Wireless Utility and the drivers Figure 3-5 Confirm the Uninstalling process Figure 3-7 Uninstalling process finished ¾ Current Network Information Chapter 4 Software Configuration4.1 Station Mode Configuration 4.1.1.1 General Connection Setting ¾ You can click “Change” button to change general connection settings Figure 4-2 More setting Figure 4-3 More setting-Click Change Figure 4-4 More setting-WEP 4.1.1.2 WEP Encryption 4.1.1.3 WPA/WPA2 Authentication with TKIP/AES Encryption ¾ Click on the WPA Encryption Setting button Figure 4-8 WPA setting ¾ Protocol Select TLS from the drop-down list 4.1.1.5 Profiles 4.1.1.4 WPA-PSK Authentication 4.1.1.6 Advanced Settings 4.2 Wireless network mode configuration Figure 4-15 Access point setting Chapter 5 Examples for application 5.1 Configuration of WEP Encryption Step Step 3：ClickStep 6 ： Step One： Select “Access Point” from the drop down list 5.2 Configuration of PSP ModeThere is two parts of this setting： Part 1：Configuration of our TL-WN322G 54M Wireless USB Adapter Remark Step Six：Select address settings mode-Easy Step Ten： Select ”Test Connection” Step Nine： ”Proxy Server” select ”Do Not Use” Appendix A Glossary ¾ AES- Advanced Encryption Standard ¾ TLS- Transport Layer Security ¾ PEAP- Protected Extended Authentication Protocol¾ RADIUS- Remote Authentication Dial In User Service ¾ PSK- Pre-Shared Key ¾ TKIP- Temporal Key Integrity Protocol Safety& Emissions Appendix B SpecificationsMedia Access Transmit Power Appendix C Contact Information