TL-WN322G 54M Wireless USB Adapter User Guide | TP-Link specs

Step Six：Select address settings mode—Easy

TL-WN322G54M Wireless USB Adapter User Guide

Step Four： Select SCAN, and let PSP scan the nearer AP automatic，then choose the default network SSID WLAN_AP of TL-WN322G 54M Wireless USB Adapter.

Step Five： ”WLAN Security Setting” If you haven’t set pass phrase. select the first ”None” .if you have set the pass phase, select the second “WEP”, the pass phase must identical with WEP key that you have set.

Step Six：Select address settings mode—Easy

Step Seven： In “IP Address Setting”screen ,we select “Manual”

Step Eight：In ”Address Setting” screen, please set IP address

- 28 -

Image 33

TP-Link manual TL-WN322G 54M Wireless USB Adapter User Guide, Step Six：Select address settings mode-Easy

Contents

Page All rights reserved COPYRIGHT & TRADEMARKS FCC RF Radiation Exposure Statement FCC STATEMENTIMPORTANT NOTE FCC Radiation Exposure Statement CE Declaration of Conformity ¾ EN 301 489-1 V.1.4.1 2002 / EN 301 489-17 V.1.2.1 ¾ EN 60950-1 ¾ EN 300 328 V.1.4.1 Chapter Package Contents TL-WN322G 54M Wireless USB Adapter User Guidey Drivers and Utility LED Indicator 1.1 FeaturesChapter 1 Introduction 1.2 LED Status 1.4 Network Configuration Ad-hoc peer-to-peer ModeInfrastructure Mode Figure 1-2 Infrastructure mode Chapter 2 Installation Guide 2.2 Installing the Drivers2.1 Before You Begin Figure 2-2 Install Shield-Choose Destination Location Figure 2-3 Install Shield-Setup Status¾ Wait a few moments until the files are copied to the computer Figure 2-4 Installation Complete Chapter 3 Uninstall Guide 1. Click on Start Settings Control Panel Add or Remove Programs3.1 Through Control Panel 3.2 Through Programs TL-WN322G Wireless Utility Figure 3-6 Uninstalling TL-WN322G Wireless Utility and the drivers Figure 3-5 Confirm the Uninstalling process Figure 3-7 Uninstalling process finished 4.1 Station Mode Configuration Chapter 4 Software Configuration4.1.1.1 General Connection Setting ¾ Current Network Information ¾ You can click “Change” button to change general connection settings Figure 4-2 More setting Figure 4-3 More setting-Click Change Figure 4-4 More setting-WEP 4.1.1.2 WEP Encryption 4.1.1.3 WPA/WPA2 Authentication with TKIP/AES Encryption ¾ Click on the WPA Encryption Setting button Figure 4-8 WPA setting ¾ Protocol Select TLS from the drop-down list 4.1.1.5 Profiles 4.1.1.4 WPA-PSK Authentication 4.1.1.6 Advanced Settings 4.2 Wireless network mode configuration Figure 4-15 Access point setting Chapter 5 Examples for application 5.1 Configuration of WEP Encryption Step 3：Click Step 6 ：Step There is two parts of this setting： 5.2 Configuration of PSP ModePart 1：Configuration of our TL-WN322G 54M Wireless USB Adapter Step One： Select “Access Point” from the drop down list Remark Step Six：Select address settings mode-Easy Step Ten： Select ”Test Connection” Step Nine： ”Proxy Server” select ”Do Not Use” Appendix A Glossary ¾ RADIUS- Remote Authentication Dial In User Service ¾ PEAP- Protected Extended Authentication Protocol¾ PSK- Pre-Shared Key ¾ TKIP- Temporal Key Integrity Protocol ¾ AES- Advanced Encryption Standard ¾ TLS- Transport Layer Security Media Access Appendix B SpecificationsTransmit Power Safety& Emissions Appendix C Contact Information