：Click, Step | TP-Link TL-WN322G manual

Step 3：Click

TL-WN322G54M Wireless USB Adapter User Guide

Step 3：Click

“Change”

Figure 5-3

In WEP key setting dialogue box click “change" to continue our setting.

¾Key length： 64 bit

¾Default key ID：#1

¾Key format：Hexadecimal

¾Key value：enter “1111111111” in #1

Click the close button in top right left of the screen, and it will return to the screen of wireless utility. till now we have finished WEP encryption configuration.

Step 6 ：

Click here.

Step 4 ： Set the options as the picture show, these are the same as the Access Point.

	Step	5 ： Click
	“Apply”	to finish
Figure 5-4	your settings.

Click the “”

- 25 -

Image 30

TP-Link manual ：Click, Step, TL-WN322G 54M Wireless USB Adapter User Guide

Contents

Page COPYRIGHT & TRADEMARKS All rights reserved IMPORTANT NOTE FCC Radiation Exposure Statement FCC STATEMENTFCC RF Radiation Exposure Statement CE Declaration of Conformity ¾ EN 300 328 V.1.4.1 ¾ EN 301 489-1 V.1.4.1 2002 / EN 301 489-17 V.1.2.1 ¾ EN 60950-1 Chapter Package Contents TL-WN322G 54M Wireless USB Adapter User Guidey Drivers and Utility Chapter 1 Introduction 1.1 FeaturesLED Indicator 1.2 LED Status 1.4 Network Configuration Ad-hoc peer-to-peer ModeInfrastructure Mode Figure 1-2 Infrastructure mode Chapter 2 Installation Guide 2.2 Installing the Drivers2.1 Before You Begin Figure 2-2 Install Shield-Choose Destination Location Figure 2-3 Install Shield-Setup Status¾ Wait a few moments until the files are copied to the computer Figure 2-4 Installation Complete Chapter 3 Uninstall Guide 1. Click on Start Settings Control Panel Add or Remove Programs3.1 Through Control Panel TL-WN322G Wireless Utility 3.2 Through Programs Figure 3-5 Confirm the Uninstalling process Figure 3-6 Uninstalling TL-WN322G Wireless Utility and the drivers Figure 3-7 Uninstalling process finished 4.1.1.1 General Connection Setting Chapter 4 Software Configuration4.1 Station Mode Configuration ¾ Current Network Information Figure 4-2 More setting ¾ You can click “Change” button to change general connection settings Figure 4-3 More setting-Click Change Figure 4-4 More setting-WEP 4.1.1.2 WEP Encryption 4.1.1.3 WPA/WPA2 Authentication with TKIP/AES Encryption ¾ Click on the WPA Encryption Setting button Figure 4-8 WPA setting ¾ Protocol Select TLS from the drop-down list 4.1.1.4 WPA-PSK Authentication 4.1.1.5 Profiles 4.1.1.6 Advanced Settings 4.2 Wireless network mode configuration Figure 4-15 Access point setting 5.1 Configuration of WEP Encryption Chapter 5 Examples for application Step 3：Click Step 6 ：Step Part 1：Configuration of our TL-WN322G 54M Wireless USB Adapter 5.2 Configuration of PSP ModeThere is two parts of this setting： Step One： Select “Access Point” from the drop down list Remark Step Six：Select address settings mode-Easy Step Nine： ”Proxy Server” select ”Do Not Use” Step Ten： Select ”Test Connection” Appendix A Glossary ¾ PSK- Pre-Shared Key ¾ TKIP- Temporal Key Integrity Protocol ¾ PEAP- Protected Extended Authentication Protocol¾ RADIUS- Remote Authentication Dial In User Service ¾ AES- Advanced Encryption Standard ¾ TLS- Transport Layer Security Transmit Power Appendix B SpecificationsMedia Access Safety& Emissions Appendix C Contact Information