TL-WN322G 54M Wireless USB Adapter User Guide | TP-Link guide

Figure 4-8 WPA setting

TL-WN322G54M Wireless USB Adapter User Guide

Figure 4-8 WPA setting

¾Protocol: Select TLS from the drop-down list.

¾User Name: Enter the user name that is used for authentication purposes.

¾Passphrase: Enter a WPA passphrase. For ASCII text, enter 8-63 characters, for hexadecimal enter 64 characters).

¾Certificate: Make sure that you have downloaded and installed the certificate on the computer. Then select the appropriate certificate from the drop-down list.

¾Click on the Apply button to save the changes.

The PEAP authentication type is based on EAP TLS authentication, but uses a password instead of a client certificate for authentication. PEAP uses a dynamic session-based WEP key, which is derived from the device and RADIUS server, to encrypt data.

- 19 -

Image 24

TP-Link TL-WN322G 54M Wireless USB Adapter User Guide, 8 WPA setting ¾ Protocol Select TLS from the drop-down list

Contents

Page COPYRIGHT & TRADEMARKS All rights reserved FCC STATEMENT FCC RF Radiation Exposure StatementIMPORTANT NOTE FCC Radiation Exposure Statement CE Declaration of Conformity ¾ EN 300 328 V.1.4.1 ¾ EN 301 489-1 V.1.4.1 2002 / EN 301 489-17 V.1.2.1 ¾ EN 60950-1 Chapter Package Contents TL-WN322G 54M Wireless USB Adapter User Guidey Drivers and Utility 1.1 Features LED IndicatorChapter 1 Introduction 1.2 LED Status 1.4 Network Configuration Ad-hoc peer-to-peer ModeInfrastructure Mode Figure 1-2 Infrastructure mode Chapter 2 Installation Guide 2.2 Installing the Drivers2.1 Before You Begin Figure 2-2 Install Shield-Choose Destination Location Figure 2-3 Install Shield-Setup Status¾ Wait a few moments until the files are copied to the computer Figure 2-4 Installation Complete Chapter 3 Uninstall Guide 1. Click on Start Settings Control Panel Add or Remove Programs3.1 Through Control Panel TL-WN322G Wireless Utility 3.2 Through Programs Figure 3-5 Confirm the Uninstalling process Figure 3-6 Uninstalling TL-WN322G Wireless Utility and the drivers Figure 3-7 Uninstalling process finished Chapter 4 Software Configuration 4.1 Station Mode Configuration4.1.1.1 General Connection Setting ¾ Current Network Information Figure 4-2 More setting ¾ You can click “Change” button to change general connection settings Figure 4-3 More setting-Click Change Figure 4-4 More setting-WEP 4.1.1.2 WEP Encryption 4.1.1.3 WPA/WPA2 Authentication with TKIP/AES Encryption ¾ Click on the WPA Encryption Setting button Figure 4-8 WPA setting ¾ Protocol Select TLS from the drop-down list 4.1.1.4 WPA-PSK Authentication 4.1.1.5 Profiles 4.1.1.6 Advanced Settings 4.2 Wireless network mode configuration Figure 4-15 Access point setting 5.1 Configuration of WEP Encryption Chapter 5 Examples for application Step 3：Click Step 6 ：Step 5.2 Configuration of PSP Mode There is two parts of this setting：Part 1：Configuration of our TL-WN322G 54M Wireless USB Adapter Step One： Select “Access Point” from the drop down list Remark Step Six：Select address settings mode-Easy Step Nine： ”Proxy Server” select ”Do Not Use” Step Ten： Select ”Test Connection” Appendix A Glossary ¾ PEAP- Protected Extended Authentication Protocol ¾ RADIUS- Remote Authentication Dial In User Service¾ PSK- Pre-Shared Key ¾ TKIP- Temporal Key Integrity Protocol ¾ AES- Advanced Encryption Standard ¾ TLS- Transport Layer Security Appendix B Specifications Media AccessTransmit Power Safety& Emissions Appendix C Contact Information