Manuals
/
TP-Link
/
Computer Equipment
/
Network Card
TP-Link
TL-WN822N
manual
Industry Canada Statement, Korea Warning Statements, NCC Notice
Models:
TL-WN822N
1
5
42
42
Download
42 pages
2.36 Kb
1
2
3
4
5
6
7
8
Specifications
Install
Main Features
To connect using QSS
Page 5
Image 5
Page 4
Page 6
Page 5
Image 5
Page 4
Page 6
Contents
TL-WN822N
300Mbps High Gain Wireless N USB Adapter
COPYRIGHT & TRADEMARKS
FCC RF Radiation Exposure Statement
FCC STATEMENT
National Restrictions
CE Mark Warning
Country
Restriction
NCC Notice
Industry Canada Statement
Korea Warning Statements
Page
Shennan Rd, Nanshan, Shenzhen, China
DECLARATION OF CONFORMITY
The product carries the CE Mark
CONTENTS
Conventions
Package Contents
TL-WN822N 300Mbps High Gain Wireless N USB Adapter
Note
1.1 Product Overview
1.2 Main Features
Chapter 1 Introduction
Working Status
1.3 Hardware Overview
Status
2.2 Software Installation
Chapter 2 Installation
2.1 Hardware Installation
TL-WN822N 300Mbps High Gain Wireless N USB Adapter
TL-WN822N
300Mbps High Gain Wireless N USB Adapter
6. The utility and drivers will install. This may take 1~2 minutes
5. Click Install to continue the setup
7. After all the steps above, you will see the screen below. Click Finish to complete the setup
3.1 To connect using TWCU TP-LINK Wireless Configuration Utility
Chapter 3 Connect to a Wireless Network
3. If word None appears behind the SSID, this means the network to be connected is not security-enabled and you can connect to the network without entering a key. To prevent outside intrusion and safeguard your network, it is strongly recommended that you set a password to your router or access point
4. You have now successfully connected to your network. Click Close to enjoy the Internet
3.2.1 PBC Push Button Configuration method
3.2 To connect using QSS
TL-WN822N
3.2.2 PIN method
2. The adapter will be connecting to the target network
TL-WN822N 300Mbps High Gain Wireless N USB Adapter
3.3.1 In Windows
3.3 To connect using Windows built-in wireless utility
3. You have now successfully connected to the network
3.3.2 In Windows Vista
1. Open the wireless utility by right-clicking on the wireless computer icon in your system tray as shown in the figure below. Select Connect to a network
3.3.3 In Windows XP
TL-WN822N
2. Right-click on the wireless computer icon in your system tray lower-right corner. Select View Available Wireless Networks
4.1 Profile
Chapter 4 Management
The following items can be found on the screen
4.1.3 Delete a profile
4.1.2 Modify a profile
4.2 Advanced
4.3 About
Chapter 5 AP Mode
SoftAP mode Select to enable or disable the function
6.2 Uninstall the driver software from your PC
Chapter 6 Uninstall Software
6.1 Uninstall the utility software from your PC
Figure 6-2 Device Manager
300Mbps High Gain Wireless N USB Adapter
Appendix A Specifications
Operation Temperature
0~40 32~104
Appendix B Glossary
Spread Spectrum - Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband transmission, but the trade off produces a signal that is, in effect, louder and thus easier to detect, provided that the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives, Direct Sequence Spread Spectrum DSSS and Frequency Hopping Spread Spectrum FHSS
Top
Page
Image
Contents
