Manuals / Brands / Personal Care / Wheelchair / Trane / Personal Care / Wheelchair

Trane Direct-Fired Indoor and Outdoor Make-Up Air Units, MUA-SVP01A-EN Menu Selection

1 58

Download 58 pages, 1.42 Mb

MUA-SVP01A-EN • Direct-Fired Indoor and Outdoor Units 43

Menu Selection Tree for BACview

This section will assist the user in navigating the menu functions of the control

program. For convenience Hotkeys are provided to allow the user to jump

directly to a specific menu heading. Simply press and hold the FN key. While

holding the FN key, press the number key of the desired menu, and it will appear.

The number key associated with the menu heading is shown below. Links to

other menu headings are also available by pressing one of the 4 keys located

directly below the screen.

UNIT MODES HOTKEY - 2

Auto/Off/Man

•Auto

•Off

•Manual

Damper Mode

•MA Temp Ctrl

• Bldg Pressure Ctrl

•Manual Ctrl

Home

Setpoints

Menu Selection

Figure 4. Menu selection tree for BACview

Contents

Main Overview NETWORKING ADAPTAIRE DEFAULT SETTINGS Page Contents Unit Operating Modes Functions Diagnostics Menu Selection Contents Thermostat Output Curve Airflow Station Layout I/O Zone 583 Controller Specifications Typical Wiring Schematic Unit Operating Modes MDT Controls: MRT Controls: MRT-Pro Controls: Page MRT-Expert Controls: Page Heating/Ventilating/Cooling Operating Modes Heating Mode General Burner Control Page Ventilation Mode Cooling Mode Figure 1. Cooling Mode Damper Control Modes Manual Mode Mixed Air Temperature Mode Building Pressure Mode Functions 100% Outside Air Minimum Ventilation Freezestat Clogged Filter User Configured PID Control DIRECT ACTING Page REVERSE ACTING Page Unit Resets Multiplexed Inputs Clock Set Diagnostics Critical Fault Codes FAULT CODE: Low Discharge Temperature Page SOLUTION: If burner was not operating prior to shutdown (check prior alarm log) FAULT CODE: Safety Circuit Open SOLUTION:If fan is running (check prior alarm log) FAULT CODE:Burner Status FAULT CODE: Burner Hand FAULT CODE: Flame Failure Diagnostics - Non-Critical Fault Codes FAULT CODE: Unit off/Fan on SOLUTION: If fan is running SOLUTION: If fan is not running FAULT CODE:Unit on/Fan off SOLUTION:If fan/motor is running SOLUTION: If fan/motor is not running FAULT CODE: Check Airflow Switches SOLUTION:If high airflow switch is opening. Do not adjust the switch setpoints SOLUTION:If low airflow switch is opening. Do not adjust the switch setpoints FAULT CODE: Clogged Filter Switch SOLUTION:If clogged filter switch is closing. FAULT CODE:Energy Save Mode 1 SOLUTION:If setpoints are misadjusted SOLUTION:If setpoints are not misadjusted FAULT CODE:Energy Save Mode 2 SOLUTION: If OAT, RoomT or DAT are such that heat is required FAULT CODE:Energy Save Mode 3 SOLUTION: If OAT, RoomT or DAT are such that heat is required SOLUTION: If setpoints are misadjusted FAULT CODE:Insufficient OA SOLUTION:If heat is desired SOLUTION:If less outside air is desired Page Menu Selection Tree for BACview UNIT MODES HOTKEY - 2 Menu Selection Status Alarm SET POINTS HOTKEY - 3 STATUS MENU HOTKEY - 4 Note: The Status Menu always displays the current status of the fan, burner and cooling. ALARM HOTKEY - 1 Alarm History (64 Most Recent) RESETS HOTKEY - 6 SCHEDULES HOTKEY- 7 USER CONFIGURABLE OUTPUT HOTKEY - 8 CLOCKSET HOTKEY - 0 HELP HOTKEY - 5 FUEL SELECT HOTKEY - 9 10 K Ohms Thermistor Output Curve Thermostat Output Curve Resistance (Ohms) Typical 10,000 Ohm Thermistor Output Curve Resistance (Ohms) Typical 10,000 Ohm Thermistor Output Curve Page I/O Zone 583 Controller Specifications I/O Zone 583 Controller Specifications OUTPUT ASSIGNMENTS - ANALOG RNET MRT-Pro or Room Air sensor OUTPUT ASSIGNMENTS - DIGITAL INPUT ASSIGNMENTS - UNIVERSAL