Manuals / Brands / Personal Care / Wheelchair / Trane / Personal Care / Wheelchair

Trane Direct-Fired Indoor and Outdoor Make-Up Air Units, MUA-SVP01A-EN Thermostat Output Curve

1 58

Download 58 pages, 1.42 Mb

MUA-SVP01A-EN • Direct-Fired Indoor and Outdoor Units 49

10 K Ohms Thermistor Output Curve

Thermostat Output CurveFigure 5. Uses FG.figure#Figure 6. Uses FG.figure#

Typical 10,000 Ohm Thermistor Output Curve

10000

20000

30000

40000

50000

60000

70000

80000

90000

100000

110000

120000

130000

140000

150000

160000

170000

180000

-22 -4 14 32 41 50 59 68 77 86 95 104 113 122 131 140 149

Temperature in Degrees F

Resistance (Ohms)

Typical 10,000 Ohm Thermistor Output Curve

5000

10000

15000

20000

25000

30000

32 41 50 59 68 77 86 95 104

Temperature in Degrees F

Resistance (Ohms)

Contents

Main Overview NETWORKING ADAPTAIRE DEFAULT SETTINGS Page Contents Unit Operating Modes Functions Diagnostics Menu Selection Contents Thermostat Output Curve Airflow Station Layout I/O Zone 583 Controller Specifications Typical Wiring Schematic Unit Operating Modes MDT Controls: MRT Controls: MRT-Pro Controls: Page MRT-Expert Controls: Page Heating/Ventilating/Cooling Operating Modes Heating Mode General Burner Control Page Ventilation Mode Cooling Mode Figure 1. Cooling Mode Damper Control Modes Manual Mode Mixed Air Temperature Mode Building Pressure Mode Functions 100% Outside Air Minimum Ventilation Freezestat Clogged Filter User Configured PID Control DIRECT ACTING Page REVERSE ACTING Page Unit Resets Multiplexed Inputs Clock Set Diagnostics Critical Fault Codes FAULT CODE: Low Discharge Temperature Page SOLUTION: If burner was not operating prior to shutdown (check prior alarm log) FAULT CODE: Safety Circuit Open SOLUTION:If fan is running (check prior alarm log) FAULT CODE:Burner Status FAULT CODE: Burner Hand FAULT CODE: Flame Failure Diagnostics - Non-Critical Fault Codes FAULT CODE: Unit off/Fan on SOLUTION: If fan is running SOLUTION: If fan is not running FAULT CODE:Unit on/Fan off SOLUTION:If fan/motor is running SOLUTION: If fan/motor is not running FAULT CODE: Check Airflow Switches SOLUTION:If high airflow switch is opening. Do not adjust the switch setpoints SOLUTION:If low airflow switch is opening. Do not adjust the switch setpoints FAULT CODE: Clogged Filter Switch SOLUTION:If clogged filter switch is closing. FAULT CODE:Energy Save Mode 1 SOLUTION:If setpoints are misadjusted SOLUTION:If setpoints are not misadjusted FAULT CODE:Energy Save Mode 2 SOLUTION: If OAT, RoomT or DAT are such that heat is required FAULT CODE:Energy Save Mode 3 SOLUTION: If OAT, RoomT or DAT are such that heat is required SOLUTION: If setpoints are misadjusted FAULT CODE:Insufficient OA SOLUTION:If heat is desired SOLUTION:If less outside air is desired Page Menu Selection Tree for BACview UNIT MODES HOTKEY - 2 Menu Selection Status Alarm SET POINTS HOTKEY - 3 STATUS MENU HOTKEY - 4 Note: The Status Menu always displays the current status of the fan, burner and cooling. ALARM HOTKEY - 1 Alarm History (64 Most Recent) RESETS HOTKEY - 6 SCHEDULES HOTKEY- 7 USER CONFIGURABLE OUTPUT HOTKEY - 8 CLOCKSET HOTKEY - 0 HELP HOTKEY - 5 FUEL SELECT HOTKEY - 9 10 K Ohms Thermistor Output Curve Thermostat Output Curve Resistance (Ohms) Typical 10,000 Ohm Thermistor Output Curve Resistance (Ohms) Typical 10,000 Ohm Thermistor Output Curve Page I/O Zone 583 Controller Specifications I/O Zone 583 Controller Specifications OUTPUT ASSIGNMENTS - ANALOG RNET MRT-Pro or Room Air sensor OUTPUT ASSIGNMENTS - DIGITAL INPUT ASSIGNMENTS - UNIVERSAL