![Twisted Pair Connector/10BaseT Connection](/images/new-backgrounds/111437/11143721x1.webp)
Twisted Pair Connector/10BaseT Connection
To connect 10BaseT Cable to Model 1004 Repeater
1.Locate or build 10BaseT cables that are:
•802.3 compliant (See page 18)
•correct (straight through or crossover) cable configuration for site installation (See page 6)
•male
2.Connect male
NOTE: Use MDI Switch to change polarity of
3.Connect male
wall plate | |
| |
| #1 |
T R A N S I T I | O N |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 |
| |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
MDI switch set for cascade
#2
T R A N S I T I O N |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| T R A N S I T I O N |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
1 |
| 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 |
|
| 1 |
| 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 |
| ||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
MDI switch set for cascade
11 | Model 1004 |
Installing Slide-In Cards
CAUTION: Wear a grounding device and observe electrostatic discharge precautions when installing
NOTE:
SQE Switch
To install a
1.Determine if the
NOTE: SQE switches must be set to the following OFF positions:
• | UTP/STP card | TOWARD |
• | Thinnet card | TOWARD |
• | AWAY FROM | |
• | Not Applicable | |
• | Fiber Optic card | TOWARD |
• | Redundant Fiber Optic | SQE jumper setting on board should be |
|
| labeled; if not, holding card with |
|
| connector at top, jumper two leftmost pins. |
• | Bridge | Not Applicable |
2.With the
3.Firmly push the card into the slot until the
4.Rotate the
8 |