Manuals / Transition Networks / Computer Equipment / Switch

Transition Networks SISGM1040-244 user manual Troubles shooting

Models: SISGM1040-244

1 117

Download 117 pages 29.94 Kb

Page 117

Transition Networks

SISGM1040-244

System Reboot interface

Troubles shooting

Verify that you are using the right power cord/adapter (DC 12 ~ 48V). Don’t use a power adapter with DC output higher than 48V, or it may damage the switch.

Select the proper UTP cable to construct your network. Please check that you are using the right cable. Use unshielded twisted-pair (UTP) or shield twisted-pair (STP) cable for RJ-45 connections: 100Ω Category 3, 4, or 5 cable for 10Mbps connections, 100Ω Category 5 cable for 100Mbps, or 100Ω Category 5e/above cable for 1000Mbps connections. Also be sure that the length of any twisted-pair connection does not exceed 100 meters (328 feet).

Diagnosing LED Indicators: the Switch can be easily monitored through panel indicators, which describes common problems you may encounter and where you can find possible solutions, to assist in identifying problems.

IF the power indicator does not light on when the power cord is plugged in, you may have a problem with power cord. Then check for loose power connections, power losses or surges at power outlet. IF you still cannot resolve the problem, contact your local dealer for assistance.

If the Industrial Switch LED indicators are normal while the connected cables are correct, but the packets still cannot transmit. Please check your system’s Ethernet devices’ configuration or status.

24-Hour Technical Support: 1-800-260-1312

International: 00-1-952-941-7600

Image 117

Transition Networks SISGM1040-244 user manual Troubles shooting

Contents

SISGM1040-244 Content Hardware Installation Web-Based Management System Event Log Syslog Configuration 101 110 SFP Advantage IntroductionSFP with DMI Digital Monitoring Interface function Dual Power InputHigh-Speed Transmissions Flexible MountingEasy Troubleshooting Wide Operating TemperatureGvrp FeaturesTransition Networks SISGM1040-244 Technical Specification Power Consumption DiagnosticsPower Input Fault OutputFree Fall ShockVibration Packing List Safety PrecautionFront Panel Hardware DescriptionTop View Wiring the Power InputsLED LED IndicatorsRJ-45 Pin Assignments Pin Number PortsCabling Pin MDI-X Signal Name MDI Signal NameTransceiver to the SFP module Transceiver Inserted LC connector to the transceiver Remove LC connector Pull out from the SFP module DIN-Rail Mounting Mounting InstallationWall Mount Plate Mounting Transition Networks SISGM1040-244 Installation Steps Hardware InstallationCoupling Ring Application Ring ApplicationDual Homing Application Console Management Connecting to the Console PortLogin in the Console Interface DB9 Connector RJ-45 ConnectorPin Assignment Hour Technical Support International CLI Management Modes Access Prompt Exit About This Mode1 Method Commands LevelSystem Name Commands Set List System Commands SetSystem Location PasswordSystem Description System ContactSubnet mask HoursIP address Portid Port Commands SetFull half 101001000autoValue Enable Disable Trunk Commands Set No aggregator lacp Show aggregatorGroupID No aggregator groupVlan Commands Set DMI Commands SetGroup Name PortNumbersPortNumber UntaggedVIDTaggedVID List Spanning Tree Commands Set ~61440Seconds Hello-time seconds Spanning-treeForward-time seconds Stp-path-costTrueFalse AutoTrueFalseIgmp Commands Set QOS Commands SetMac / Filter Table Commands Set Snmp Commands Set NoAuthNoPrivAuthNoP RivAuthPriv NameExactPrifix Read View Name Write View Name Notify ViewRemove specified Switchconfig#no snmpv3 Port Mirroring Commands SetIv match-rule Exact views V1 RXTXBothPort ID 802.1x Commands SetWords SecNumber Tftp Commands Set Disable reject acceptAuthorize Clientserverboth SystemLog, Smtp and Event Commands SetAccount Index Email addressLink-UPLink-DownBot SystemlogSMTPBothStart time End time Sntp Commands SetMinute Timezone1st Ring Port 2nd Ring Ring Commands SetCoupling Port Control PortPreparing for Web Management About Web-based ManagementSystem Login Main interface System Information IP ConfigurationDhcp Server System configuration Dhcp Client System Configuration Dhcp Server Port and IP Bindings Tftp Update FirmwareTftp Backup Configuration Tftp Restore ConfigurationBackup File Name fill the file name System Event Log Syslog ConfigurationSystem Event Log Smtp Configuration Server IP Address column System Event Log Event Configuration Hour Technical Support International Fault Relay Alarm Sntp ConfigurationLocal Time Zone Conversion from UTC Time at 1200 UTC Transition NetworksSISGM1040-244 Switch Timer Displays the switch current time Click Daylight Saving Offset mins set up the offset timeIP Security New configuration will lose when switch power offUser Authentication Port Statistics Button to clean all countsPort Control Port Trunk Aggregator settingAggregator Information Active status will be created automatically State ActivityPort Mirroring Rate Limiting DMI Digital Monitoring Interface Vlan configuration Vlan configuration Port-based Vlan Transition Networks SISGM1040-244 Vlan Port Based interface New configuration will lose when switch power off 802.1Q Vlan Hybrid Link Both Access Link and Trunk Link are available 802.1Q ConfigurationGroup Configuration Rapid Spanning Tree Rstp System ConfigurationDelay Time Rstp Port Configuration Snmp Configuration Community Strings System ConfigurationTrap Configuration SNMPV3 Configuration Context TableUser Profile Page Access Table Group TableMIBview Table QoS Policy and Priority Type QoS ConfigurationPort Base Priority Igmp Configuration COS ConfigurationTOS Configuration Query Message DescriptionReport LeaveRing Ring and Rstp function cannot exist at the same time Security 802.1x Per Port Configuration Misc Configuration Add the Static MAC Address MAC Address TableMAC Filtering All MAC Addresses Factory Default Save ConfigurationSystem Reboot Troubles shooting