Tripp Lite PVX700 Service, Maintenance, Troubleshooting, Specifications, Limited Warranty

Service

If you are returning your Inverter to Tripp Lite, please pack it carefully, using the ORIGINAL PACKING MATERIAL that came with the unit. Enclose a letter describing the symptoms of the problem. If the Inverter is within the warranty period, enclose a copy of your sales receipt. To obtain service you must obtain a Returned Material Authorization (RMA) number from Tripp Lite or an authorized Tripp Lite service center.

Maintenance

Your Inverter requires no maintenance and contains no user-serviceable or replaceable parts, but should be kept dry at all times. Periodically check, clean and tighten all cable connections as necessary, both at the unit and at the battery.

Troubleshooting

Please check the following before sending the Inverter in for service:

Symptom	Problem	Correction
Alarm sounds.	Low battery voltage (<10.5 V).	Turn Inverter OFF and run engine to recharge vehicle battery.
	Output overload.	Turn Inverter OFF and remove overload by unplugging high-wattage devices. Load
		should not exceed your Inverter's maximum continuous output power (see Specifications).
Inverter does not turn ON when	Automatic Inverter shutdown due to low battery	Turn Inverter OFF and run engine to
power switch is turned ON.	voltage (<10V).	recharge vehicle battery.
	Automatic Inverter shutdown due to output overload.	Turn Inverter OFF and remove overload by unplugging high-wattage devices. Load
		should not exceed your Inverter’s maximum continuous output power (see Specifications).
	Blown fuse.	Replace fuse with standard automotive fuse of identical amperage (see Specifications).
Inverter is unable to power	Battery running low. Low battery voltage reduces	Turn Inverter OFF and run engine to recharge vehicle battery.
connected equipment.	Inverter power output.
	Connected equipment load exceeds Inverter’s	Turn Inverter OFF and remove overload by unplugging high-wattage devices. Load
	maximum continuous output power.	should not exceed your Inverter's maximum continuous output power (see Specifications).
Connected equipment experiences	Loose connections.	Check and secure all connections.
audio/video distortion.
	Audio/video interference.	Reposition equipment antennas and Inverter.

Specifications

Model:	PVX700
Output Power (Maximum Continuous Watts)*:	700
Output Power (Peak Watts)**:	1400
Input Voltage (DC):	12V nominal (10-15V)
Output Voltage (AC)/Frequency:	230V / 50 Hz. nominal
Output Waveform:	PWM Sine Wave
Low Battery Voltage Alarm (Volts):	10.5V
Low Battery Voltage Shutdown (Volts):	10V
AC Outlets:	1
Circuit Protection (Minimum DC Fuse Rating):	125-amp fuse (external)
Minimum Battery Cable Size:	6 AWG (4 mm)
Maximum Battery Cable Size:	4 AWG (5 mm)
Ground Cable Size:	12-18 AWG (1-2 mm)
Housing Material:	Extruded Aluminum

*Maximum output power (continuous or peak) only available when vehicle battery is properly charged. Run vehicle engine often to maintain proper charge. ** Peak Output Power is instantaneous.

Typical Runtimes Before Battery Recharge

Although you can operate your Inverter with your vehicle engine off, best results are usually attained with the engine running. Since the Inverter converts electrical energy (and doesn’t produce it), the Inverter’s performance is relative to the condition of your vehicle’s electrical system (battery, alternator and wiring). If other loads (air conditioner, heater, lights, etc.) are also using power, you may get less runtime.

	With Typical	With Typical	With Typical
	Compact Vehicle	Mid-Size Vehicle	Full-Size Vehicle
	(4 cylinder) Battery,	(6 cylinder) Battery,	(8 cylinder) Battery,
Model: PVX700	Alternator & Wiring	Alternator & Wiring	Alternator & Wiring
1/2 Load (engine ON)	continuous	continuous	continuous
Full Load* (engine ON)	1-2 hours	2-4 hours	continuous
1/2 Load (engine OFF)	not recommended	1 hours	2 hours
Full Load* (engine OFF)	not recommended	not recommended	1 hour

NOTE: You can maximize output power by following one or more of these steps: (1) connect multiple batteries to the Inverter; (2) keep batteries fully charged by running the vehicle's engine often; (3) install the Inverter as close to the batteries as possible; (4) connect the heaviest gauge cable possible to the Inverter's DC terminals; (5) use the Inverter in a vehicle with a heavy-duty alternator; (6) run the vehicle's engine at higher RPMs.

Battery Wiring Recommendations

For maximum efficiency, keep battery wires as short as possible. For very short runs, 6 AWG (4 mm) wiring may be adequate; for longer runs 4 AWG (5 mm) wiring is recommended. Acceptable output power is directly dependent on wire length: the shorter the wiring, the better the performance.

Limited Warranty

Tripp Lite warrants its Inverters to be free from defects in materials and workmanship for a period of 1 year from the date of initial purchase. Tripp Lite’s obligation under this warranty is limited to repairing or replacing (at its sole option) any such defective products. To obtain service under this warranty you must obtain a Returned Material Authorization (RMA) number from Tripp Lite or an authorized Tripp Lite service center. Products must be returned to Tripp Lite or an authorized Tripp Lite service center with transportation charges prepaid and must be accompanied by a brief description of the problem encountered and proof of date and place of purchase.

This warranty does not apply to equipment which has been damaged by accident, negligence or misapplication or has been altered or modified in any way, including opening of the unit’s casing for any reason. This warranty applies only to the original purchaser who must have properly registered the product within 10 days of purchase.

EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the purchaser.

EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, Tripp Lite is not liable for any costs, such as lost profits or revenue, loss of equipment, loss of use of equipment, loss of software, loss of data, costs of substitutes, claims by third parties, or otherwise.

Regulatory Compliance Identification Numbers

For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a unique series number. The series number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to the series number. The series number should not be confused with the marking name or model number of the product.

Tripp Lite has a policy of continuous improvement. Product specifications are subject to change without notice.

6