Troy-Bilt 1919 Section Maintenance, Specifications, General Maintenance Recommendations, Data Tag

Models: 1919

1 28
Download 28 pages 46.1 Kb
Page 12
Image 12
Section Maintenance

Section Maintenance

5

SPECIFICATIONS

Maximum Surge Watts . . . . . . . . . . . . . . . . . .8,550 watts Continuous Wattage Capacity . . . . . . . . . . . .5,550 watts Power Factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.0 Rated Maximum Continuous AC Load Current:

At 120 Volts . . . . . . . . . . . . . . . . . . . . . . . . .46.2 Amps At 240 Volts . . . . . . . . . . . . . . . . . . . . . . . . .23.1 Amps Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1–phase Rated Frequency . . . . . . . . . . . . . . . . . . . . . . . . .60 Hertz Fuel Tank Capacity . . . . . . . . . . . . . . . . . . . . 5 U.S. gallons Shipping Weight . . . . . . . . . . . . . . . . . . . . . . . . . . 169 lbs.

GENERAL MAINTENANCE RECOMMENDATIONS

The Owner/Operator is responsible for making sure that all periodic maintenance tasks are completed on a timely basis; that all discrepancies are corrected; and that the unit is kept clean and properly stored. NEVER operate a

damaged or defective generator.

Should you have questions about replacing components on your Troy-Bilt® generator, please call 1-888-611-6708for assistance.

NOTE: DO NOT use a garden hose to clean generator. Water can enter engine fuel system and cause problems. In addition, if water enters generator through cooling air slots, some of the water will be retained in voids and cracks of the rotor and stator winding insulation.Water and dirt buildup on the generator internal windings will eventually decrease the insulation resistance of these windings.

Generator Cleaning

• Use a damp cloth to wipe exterior surfaces clean.

CAUTION

Improper treatment of generator can damage it and shorten its life.

DO NOT expose generator to excessive moisture, dust, dirt, or corrosive vapors.

DO NOT insert any objects through cooling slots.

Use a soft bristle brush to loosen caked on dirt or oil.

Use a vacuum cleaner to pick up loose dirt and debris.

Use low pressure air (not to exceed 25 psi) to blow away dirt. Inspect cooling air slots and opening on generator. These openings must be kept clean and unobstructed.

Engine Maintenance

See engine owner’s manual for instructions.

SPECIFICATIONS CAUTION

Avoid prolonged or repeated skin contact with used motor oil.

Used motor oil has been shown to cause skin cancer in certain laboratory animals.

Thoroughly wash exposed areas with soap and water.

Data Tag

Data tag information is very important if you need help from our Customer Service Department or an authorized service dealer.

The data tag (Figure 9) is located either on the heat shield or engine support on the muffler side of the generator. For future reference, please copy the model, revision, and serial number of the generator in the space below.

Figure 9 — Data Tag

KEEP OUT OF REACH OF CHILDREN. DON'T POLLUTE. CONSERVE RESOURCES. RETURN USED OIL TO COLLECTION CENTERS.

Generator Maintenance

Generator maintenance consists of keeping the unit clean and dry. Operate and store the unit in a clean dry environment where it will not be exposed to excessive dust, dirt, moisture or any corrosive vapors. Cooling air slots in the generator must not become clogged with snow, leaves or any other foreign material.

MODEL REV NO SERIAL

AC VOLTS AC AMPS AC WATTS DC VOLTS DC AMPS

Copy Model

Number Here

Copy Revision

Here

GENERAL MAINTENANCE RECOMMENDATIONS Copy Serial Number Here

12

Page 12
Image 12
Troy-Bilt 1919 Section Maintenance, Specifications, General Maintenance Recommendations, Generator Cleaning, Data Tag