Section Operation

4

HOW TO USE YOUR PRESSURE WASHER

If you have any problems operating your pressure washer, please call the pressure washer helpline at 1-888-611-6708.

Pressure Washer Location

Pressure Washer Clearance

How to Start Your Pressure Washer

To start your pressure washer for the first time, follow these instructions step-by-step.This starting information also applies if you have let the pressure washer sit idle for at least a day.

1.Place pressure washer near an outside water source capable of supplying water at a flow rate greater than 3.3 gallons per minute and no less than 20 PSI at pressure washer end of garden hose.

WARNING

Exhaust heat/gases can ignite combustibles, structures or damage fuel tank causing a fire.

Keep at least 5 ft. (152 cm) clearance on all sides of pressure washer including overhead.

Place pressure washer in a well ventilated area, which will allow for removal of deadly exhaust gas. DO NOT place pressure washer where exhaust gas could accumulate and enter inside or be drawn into a potentially occupied building. Ensure exhaust gas is kept away from any windows, doors, ventilation intakes or other openings that can allow exhaust gas to collect in a confined area (Figure 8). Prevailing winds and air currents should be taken into consideration when positioning pressure washer.

WARNING

Running engine gives off carbon monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide can cause nausea, fainting or death.

Operate pressure washer ONLY outdoors.

Keep exhaust gas from entering a confined area through windows, doors, ventilation intakes or other openings.

DO NOT operate pressure washer inside any building or enclosure, even if doors or windows are open.

Figure 8 — Pressure Washer Clearance

Typical Pressure

Washer Shown

Exhaust Port

2.Check that high pressure hose is tightly connected to spray gun and pump. See “Preparing Pressure Washer for Use” for illustrations.

3.Make sure unit is in a level position.

4.Connect garden hose to water inlet on pressure washer pump. Turn ON water.

CAUTION

DO NOT run the pump without the water supply connected and turned on.

Damage to equipment resulting from failure to follow this instruction will void warranty.

5.Attach nozzle extension to spray gun (Figure 9). Tighten by hand.

Figure 9 — Connect Nozzle Extension to Spray Gun

6.Choose desired ProjectPro™ nozzle, pull back nozzle extension collar, insert nozzle and release collar.Tug on nozzle to make sure it is securely in place (Figure 10). See “How to Use ProjectPro™ Nozzle System”.

Figure 10 - Attaching ProjectPro™ Nozzle to Nozzle Extension

7.Engage trigger lock on spray gun trigger (Figure 11).

Figure 11 — Spray Gun with Trigger Lock Engaged

Trigger Lock

10

Page 10
Image 10
Troy-Bilt 20240 Section Operation, HOW to USE Your Pressure Washer, Pressure Washer Location, Pressure Washer Clearance

20240 specifications

The Troy-Bilt 20240 is a popular model among homeowners looking for a reliable and efficient snow thrower. Designed to tackle moderate to heavy snowfall, this snowblower boasts a range of features that enhance its performance and ease of use.

One of the standout characteristics of the Troy-Bilt 20240 is its 24-inch clearing width and 21-inch intake height, allowing it to effectively handle large amounts of snow. The powerful 243cc engine provides the necessary strength to clear driveways, sidewalks, and patios with minimal effort.

The snow thrower is equipped with a self-propelled system, enabling users to navigate through deep snow with ease. With six forward and two reverse speeds, operators can select the right speed for their working conditions, ensuring maximum efficiency and control. This versatility makes it suitable for various snow depths and terrains.

The 20240 features an adjustable chute that can rotate a full 180 degrees, allowing users to direct the snow where it is needed. This is particularly advantageous for clearing snow away from pathways or driveways without creating additional obstacles. The chute can be easily adjusted using a remote, adding to the user-friendly design of the machine.

Durability is a key aspect of the Troy-Bilt 20240. It incorporates a heavy-duty steel frame and reinforced poly skid shoes that resist wear and tear from rugged winter conditions. This robust construction ensures that the snow thrower can withstand the challenges posed by harsh weather and heavy snowfall.

Additionally, the snow blower's touch control system offers enhanced maneuverability, enabling operators to make quick adjustments on the fly. The ergonomic hand grips provide comfort during extended use, reducing fatigue and improving handling.

Another notable technology feature is the electric start, which simplifies the starting process, particularly in cold weather. This convenient option eliminates the hassle of pulling cords, making it accessible for users of all experience levels.

In summary, the Troy-Bilt 20240 combines power, durability, and advanced features, making it an excellent choice for homeowners who need an effective snow removal solution. Its impressive capabilities and user-friendly design ensure that it stands out in the competitive market of snow throwers, providing reliability and performance season after season.