Section 1: Safety Rules

WARNING

Rapid retraction of starter cord (kickback) will pull hand and arm toward engine faster than you can let go.

Broken bones, fractures, bruises or sprains could result.

•ALWAYS point gun in safe direction and squeeze spray gun trigger, to release pressure and avoid kickback each time, before starting engine. Engage trigger lock when not in use.

•When starting engine, pull cord slowly until resistance is felt and then pull rapidly to avoid kickback.

•After each starting attempt, where engine fails to run, always point gun in safe direction and squeeze spray gun trigger to release high pressure.

WARNING

Running engines produce heat.Temperature of muffler and nearby areas can reach or exceed 150°F (65°C).

Severe burns can occur on contact.

Exhaust heat/gases can ignite combustibles, structures or damage fuel tank causing a fire.

•DO NOT touch hot surfaces and avoid hot exhaust gases.

•Allow equipment to cool before touching.

•Keep at least 5 ft. (152 cm) clearance on all sides of pressure washer including overhead.

•Code of Federal Regulation (CFR) Title 36 Parks, Forests, and Public Property require equipment powered by an internal combustion engine to have a spark arrester, maintained in effective working order, complying to USDA Forest service standard 5100-1C or later revision. In the State of California a spark arrester is required under section 4442 of the California Public resources code. Other states may have similar laws.

WARNING

Starter and other rotating parts can entangle hands, hair, clothing, or accessories.

•DO NOT wear loose clothing, jewelry or anything that may be caught in the starter or other rotating parts.

•Tie up long hair and remove jewelry.

WARNING

The high pressure stream of water that this equipment produces can pierce skin and its underlying tissues, leading to serious injury and possible amputation.

Spray gun traps high water pressure, even when engine is stopped and water is disconnected, which can cause injury.

•NEVER aim spray gun at people, animals or plants.

•DO NOT allow CHILDREN to operate pressure washer.

•NEVER repair high pressure hose. Replace it.

•NEVER repair leaking connections with sealant of any kind. Replace o-ring or seal.

•Keep high pressure hose connected to pump and spray gun while system is pressurized.

•ALWAYS point gun in safe direction and squeeze spray gun trigger, to release high pressure, every time you stop engine. Engage trigger lock when not in use.

WARNING

High pressure spray can cause paint chips or other particles to become airborne.

•Always wear eye protection when using this equipment or in vicinity of where equipment is in use.

WARNING

Unintentional sparking can result in fire or electric shock.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR PRESSURE WASHER

•Disconnect spark plug wire from spark plug and place wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

•Use approved spark plug tester.

•DO NOT check for spark with spark plug removed.

4

Page 3 Page 5
Page 4
Image 4
Troy-Bilt 20240 manual Unintentional sparking can result in fire or electric shock
Page 3 Page 5

20240 specifications

The Troy-Bilt 20240 is a popular model among homeowners looking for a reliable and efficient snow thrower. Designed to tackle moderate to heavy snowfall, this snowblower boasts a range of features that enhance its performance and ease of use.

One of the standout characteristics of the Troy-Bilt 20240 is its 24-inch clearing width and 21-inch intake height, allowing it to effectively handle large amounts of snow. The powerful 243cc engine provides the necessary strength to clear driveways, sidewalks, and patios with minimal effort.

The snow thrower is equipped with a self-propelled system, enabling users to navigate through deep snow with ease. With six forward and two reverse speeds, operators can select the right speed for their working conditions, ensuring maximum efficiency and control. This versatility makes it suitable for various snow depths and terrains.

The 20240 features an adjustable chute that can rotate a full 180 degrees, allowing users to direct the snow where it is needed. This is particularly advantageous for clearing snow away from pathways or driveways without creating additional obstacles. The chute can be easily adjusted using a remote, adding to the user-friendly design of the machine.

Durability is a key aspect of the Troy-Bilt 20240. It incorporates a heavy-duty steel frame and reinforced poly skid shoes that resist wear and tear from rugged winter conditions. This robust construction ensures that the snow thrower can withstand the challenges posed by harsh weather and heavy snowfall.

Additionally, the snow blower's touch control system offers enhanced maneuverability, enabling operators to make quick adjustments on the fly. The ergonomic hand grips provide comfort during extended use, reducing fatigue and improving handling.

Another notable technology feature is the electric start, which simplifies the starting process, particularly in cold weather. This convenient option eliminates the hassle of pulling cords, making it accessible for users of all experience levels.

In summary, the Troy-Bilt 20240 combines power, durability, and advanced features, making it an excellent choice for homeowners who need an effective snow removal solution. Its impressive capabilities and user-friendly design ensure that it stands out in the competitive market of snow throwers, providing reliability and performance season after season.
Top Page Image Contents