Section 3: Assembly

Connect Hose and Water Supply to Pump

IMPORTANT: To avoid pump damage, you must assemble the nozzle extension to the spray gun and attach all hoses before you start the engine.

NOTE: Remove and discard the shipping caps from the pumps high pressure outlet and water inlet before attaching hoses.

1.Uncoil high pressure hose and attach one end of hose to base of spray gun (Figure 5).Tighten by hand.

Figure 5 — Connect High Pressure Hose to Spray Gun

Connect high pressure

hose here

2.Attach other end of high pressure hose to high pressure outlet on pump (Figure 6).Tighten by hand.

Figure 6 — Connect High Pressure Hose to Pump

3.Before connecting garden hose to water inlet, inspect inlet screen (Figure 7). Clean screen if it contains debris or have it replaced if damaged. DO NOT RUN PRESSURE WASHER IF INLET SCREEN IS DAMAGED.

Figure 7 — Connect the Garden Hose to Water Inlet

Inspect inlet

screen, DO NOT use if damaged;

clean if dirty.

4.Run water through your garden hose for 30 seconds to clean out any debris.

IMPORTANT: DO NOT siphon standing water for the water supply. Use ONLY cold water (less than 100°F).

5.Connect the garden hose (not to exceed 50 feet in length) to the water inlet.Tighten by hand (Figure 7).

CAUTION

There MUST be at least ten feet of unrestricted garden hose between the pressure washer inlet and any flow shut off device, such as a ‘Y’ shut-off connector or other convenience-type water shut-off valve.

•Damage to equipment resulting from failure to follow this instruction will void warranty.

6.Turn ON the water and squeeze the trigger on the gun to purge the pump system of air and impurities.

WARNING

High pressure spray can cause paint chips or other particles to become airborne.

•Always wear eye protection when using this equipment or in vicinity of where equipment is in use.

•Before starting the pressure washer, be sure you are wearing adequate eye protection.

Checklist Before Starting Engine

Review the unit’s assembly to ensure you have performed all of the following.

1.Make sure handle is in place and secure.

2.Check that oil has been added to proper level in the engine crankcase.

3.Add proper fuel to fuel tank.

4.Check for properly tightened hose connections.

5.Check to make sure there are no kinks, cuts, or damage to high pressure hose.

6.Provide a proper water supply at an adequate flow.

7.Be sure to read “Safety Rules” and “How To Use Your Pressure Washer” before using pressure washer.

9

Page 8 Page 10
Page 9
Image 9
Troy-Bilt 20240 Connect Hose and Water Supply to Pump, Checklist Before Starting Engine, Connect high pressure Hose here
Page 8 Page 10

20240 specifications

The Troy-Bilt 20240 is a popular model among homeowners looking for a reliable and efficient snow thrower. Designed to tackle moderate to heavy snowfall, this snowblower boasts a range of features that enhance its performance and ease of use.

One of the standout characteristics of the Troy-Bilt 20240 is its 24-inch clearing width and 21-inch intake height, allowing it to effectively handle large amounts of snow. The powerful 243cc engine provides the necessary strength to clear driveways, sidewalks, and patios with minimal effort.

The snow thrower is equipped with a self-propelled system, enabling users to navigate through deep snow with ease. With six forward and two reverse speeds, operators can select the right speed for their working conditions, ensuring maximum efficiency and control. This versatility makes it suitable for various snow depths and terrains.

The 20240 features an adjustable chute that can rotate a full 180 degrees, allowing users to direct the snow where it is needed. This is particularly advantageous for clearing snow away from pathways or driveways without creating additional obstacles. The chute can be easily adjusted using a remote, adding to the user-friendly design of the machine.

Durability is a key aspect of the Troy-Bilt 20240. It incorporates a heavy-duty steel frame and reinforced poly skid shoes that resist wear and tear from rugged winter conditions. This robust construction ensures that the snow thrower can withstand the challenges posed by harsh weather and heavy snowfall.

Additionally, the snow blower's touch control system offers enhanced maneuverability, enabling operators to make quick adjustments on the fly. The ergonomic hand grips provide comfort during extended use, reducing fatigue and improving handling.

Another notable technology feature is the electric start, which simplifies the starting process, particularly in cold weather. This convenient option eliminates the hassle of pulling cords, making it accessible for users of all experience levels.

In summary, the Troy-Bilt 20240 combines power, durability, and advanced features, making it an excellent choice for homeowners who need an effective snow removal solution. Its impressive capabilities and user-friendly design ensure that it stands out in the competitive market of snow throwers, providing reliability and performance season after season.
Top Page Image Contents