TB2040 XP
2-Cycle Trimmer
Operator’s Manual
Removing Unit From Carton | Assemble The Unit |
| |
|
|
|
|
1 |
| 2 |
Remove all contents from | Place the shield onto the | |
the carton. |
| mount bracket. Securely |
|
| screw the 4 shield screws |
|
| through the holes on the |
|
| mount bracket and into the |
|
| shield. Make sure the screws |
|
| are tightened equally. |
Assemble The Unit |
|
|
40:1 |
|
|
1 Gallon | 3.2 oz |
|
5 |
| 6 |
Mix thoroughly in separate | Place unit on a level surface. | |
fuel can: |
| Fill fuel tank. |
NOTE: Do not mix directly in fuel tank.
Starting The Unit
| Min. 6" | |
3 | 4 | |
Remove cap from end of | Put handle on shaft. Move | |
lower boom. Push cutting | handle a minimum 6 inches | |
attachment | away from shaft grip. Insert | |
coupler. Turn coupler knob | bolt and tighten. | |
clockwise to tighten. |
| |
Starting The Unit |
| |
Primer | Choke Lever | |
Bulb | ||
|
10 X
7 | 8 |
| Press primer bulb 10 times, | Move choke lever to |
or until fuel is visible | Position 1. |
| Electric Starter or |
|
| |
| Power Start Bit Optional! |
| Starter Rope | |
THESE OPTIONAL ACCESSORIES |
|
| |
ARE SOLD SEPARATELY! |
| Fuel Cap | |
This unit has an alternate starting method |
|
| |
that many find easier to use than pulling a |
|
| |
rope. Please contact a local retailer or call |
|
| |
|
| ||
Information may also be found at |
|
| |
www.troybilt.com | On/ Off Switch |
| |
| |||
| Throttle Control | ||
|
| ||
| ASSEMBLY TOOLS | ||
| REQUIRED: | ||
| • | Phillips screwdriver | |
| • | 3/8” Socket and Driver | |
|
| Need Help? | |
| Call | ||
Cutting Head Shield | DIDN’T START? | ||
Repeat these instructions. | |||
| |||
| IF engine fails to start after 2 attempts, | ||
| move choke lever to position 3 and pull | ||
| the starter rope until engine starts | ||
| IF unit still fails to start, refer to operator’s | ||
| manual for additional starting and | ||
| troubleshooting information | ||
English — Page 1
— Page 6
Choke Lever
Choke Lever
|
| 5 X |
|
|
| ||
19 | 10 | 11 | 12 | 14 | 15 | ||
13 | |||||||
Crouch in starting position. | SQUEEZE and HOLD | Pull rope 5 times. | Move choke lever to | Pull rope | Continue to squeeze | Continue to squeeze | |
| throttle for ALL further |
| Position 2 and squeeze | engine. Run unit for | throttle. Move choke lever | throttle. Run unit for an | |
| steps. |
| throttle. | seconds to warm up. | to Position 3. | additional 60 seconds to | |
|
|
|
|
|
| complete |
may be used during this time.
Reloading The Line*Quick Instructions to |
| Using a | Align the arrows on the |
Replace Trimmer Line | Rotate the bump knob | insert the tip into the line dimple, | bump knob with the |
clockwise until all line is | just under the exposed portion of | spool cover eyelets. | |
| inside the cutting head. | the line, and pull all the line out. |
|
For complete instructions, refer to Line Installation section of this manual.
Français
Español — Page 11
Using 16 ft. of 0.095 in. line; push both ends through the holes in the bump knob until they protrude through the eyelets.
Pull the line until approximately 8 ft. is visible on each side.
Hold the spool cover, turn the bump knob clockwise to wind the line around the spool until about 5 in. is protruding from each side of the cutting head.
Start the unit and bump the cutting head on the ground until the desired cutting length is achieved.
IMPORTANT: READ THE OPERATOR’S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES WHILE OPERATING THE UNIT.
NEED HELP? CALL 1-800-828-5500 IN U.S. OR 1–800–668–1238 IN CANADA
| 11/11 |