Tunturi P O R TA N T S a F E T Y S T R U C T I O N S, S E M B Ly, J9 Hand Rail and Interface

O W N E R ' S M A N U A L J 9 • J 9 F

I M P O R TA N T S A F E T Y

I N S T R U C T I O N S

This Owner’s Manual is an essential part of your training equipment: reading all instructions in this manual before you start using this appliance. The following precautions must always be followed:

WARNING:

•Never use extension cords between the treadmill and your wall outlet. The device’s maximum power consumption is 10 A (EU) / 20 A (US). Outlets with fluctuating voltage of more than 5 %, may result in erratic performance or cause damage

to treadmill electronics. Using electrical power other than that which has been specified in this manual, will ultimately void any warranty, implied or otherwise.

WARNING: to reduce any risk to persons:

•Keep hands clear of any moving parts. Never place hands, feet or any other objects into any opening or under the treadmill.

•Never leave the treadmill unattended when plugged in. Unplug from outlet when not in use, before putting on or taking off parts. To disconnect, turn all controls to the off position, then remove plug from outlet.

•Close supervision is necessary when the treadmill used by, on, or near children, invalids, or disabled persons.

•Use the treadmill only for its intended use as described in this manual. Do not use attachments not recommended by Tunturi.

•Before you start using the treadmill, make sure that it functions correctly in every way. Do not use a faulty device.

•Keep the cord away from heated surfaces.

•J9 / J9F must not be used outdoors. J9 /

J9F tolerates an environment measuring +10°C to +35°C. Air humidity must never exceed 90 %.

•Do not attempt any servicing or adjustment other than those described in this manual. The given instructions must be followed carefully.

•Never operate this treadmill if it has a damaged cord or plug, if it has been dropped or damaged, or dropped into water. Return the treadmill to a service center for repair.

•Never operate the appliance with the air opening blocked. Keep the air openings free of lint, hair, and the like.

•Do not operate where aerosol (spray)

G B

O W N E R ' S M A N U A L • J 9 • J 9 F

products are being used or where oxygen is being administered.

•Strong electromagnetic fields may cause disturbances in the heart rate measurement.

•The device must not be used by persons weighing over 135 kg (300 lbs).

SAVE THESE INSTRUCTIONS!

WELCOME TO THE WORLD OF TUNTURI

EXERCISING!

Your choice shows that you really want to invest in your well-being and condition; it also shows you really value high quality and style. With Tunturi Fitness Equipment, you’ve chosen a high-quality, safe and motivating product as your training partner. Whatever your goal in training, we are certain this is the training equipment to get you there.

A S S E M B LY

Before assembling the device, insure all parts are present:

1.Frame

2. Power cord

3. Assembly kit (contents are marked with an * in the spare part list)

In case of problems contact your Tunturi dealer. The packaging includes a disposable silicate bag for absorbing moisture during storage and transportation. The directions left, right, front and back are defined as seen from the exercising position.

J9: HAND RAIL AND INTERFACE

FIGURES 1, 2, 5 AND 6

Turn the user interface until the holes for the locking screws are in position and then attach by tightening the 4 screws on the rear side. Cut (M6x12) the green ribbon and attach the corner pieces with the transportation wheels to the lower ends of the hand rail with 3 Allen screws (M6x16) on both sides. Lift the handrail to the upright position, place the cover tubes between corner pieces and the frame and thread the attachment bolts through the tubes. Tighten the bolts with nuts. Place the multi-purpose rack with the plastic end pieces on the top of the hand rail, pull the lower edge of the rack over the support bolts on the hand rail sides and attach the plastic end pieces with screws to the top of the hand rail. Attach the 2 (M6x12) screws on the front side of the interface and remove the protective film from the display.

3