6
OWNER'S MANUAL • J9 • J9F
• Press any function key to exit the Set mode.
NOT E! Pressing the Set key during an exercise
will stop the belt and nish the exercise.
The Reset key resets energy consumption,
time and distance displays for all exercises.
DISPLAY
SEPARATE DISPLAYS
1. SP EED
Running deck speed measured in kilometres or
miles per hour (0,5-18,0 km/h / 0,3-11,2 mph).
2. TIME
Elapsed time at 1 second intervals 00:00-59:59 up
to 1 hour, and at 1 minute intervals thereafter
1:00-99:59.
3. D ISTAN CE
Accumulated distance in kilometers or miles
(0.0-999.9).
MAIN DISPLAY
1. Prole display: the letters beside the display
indicate which prole is being displayed (mph,
km/h = speed; kcal/min = energy consumption
measurement during workout; heart = heart-rate
level; up/down arrow = elevation angle)
2. Letters indicating a selected function: Manual
Control = user-controlled exercise; Pulse Control
= standard heart-rate exercise (treadmill icon
indicates the selected form of heart-rate exercise);
Proles = pre-programed exercise proles, Own
Proles = user-designed exercise proles; Test =
walking test, Recovery = measurement of recovery
pulse.
3. Number line: kcal = energy consumption; arrow
up/down = running deck elevation; heart = heart-
rate level. If heart-rate measurement is not used,
the user interface displays --. A square blinks on the
display at the pace of the measured heart rate to
indicate that measurement is in operation.
ERROR CODES
The user interface will display information about
any operational faults. An error code begins with
the abbreviation Err.
11 Motor heat protection off: Please check
running deck lubrication.
13 Running deck speed exceeds set value: Please
follow this manual’s instructions on using the
device.
15 Running deck does not respond to controls:
Please check running deck lubrication and follow
this manual’s instructions on using the device.
71 Lift motor fault or lifting motor overload
protection off: Please switch the device off for 5
minutes and then restart. If the error message does
not disappear, please contact your local Tunturi
distributor.
Remove the error code by pressing the RESET
key. If any of these error codes appears repeatedly
despite servicing, or if a code other than the above
is displayed constantly, please contact your Tunturi
dealer.
POSITION SPEED CONTROL (PSC)
Position Speed Control (PSC) allows you to adjust
running track speed by changing your position on
the track. Move to the front of the track and it
accelerates, and as you move back the track itself
slows down. When you are walking or running
in the middle section of the track the speed stays
steady.
NOT E! You must wear a Polar heart rate belt
when you use PSC ! A blinking square in the Heart
Rate display indicates that heart rate measurement
is in operation.
NOT E! Attach the holder of the safety tether
key carefully to your shirt whenever you are using
PSC. Adjust the length of the safety tether key wire
so that it will be detached from the meter, if you
move too far back.
NOT E! If you are exercising with PSC, there
must not be another heart rate transmitter near
the treadmill (minimum distance 2 m); the
simultaneous signals of two transmitters endanger
user safety by interfering with the PSC.
1. Start the use of PS C by setting the speed zone
limits. Press the PSC key.
• PSC ON is displayed. Press OK.
• SET U P YE S is displayed. Press OK.
• POSIT ION 1 YE S is displayed. Step on the track
as shown in gure Pos 1, the tips of your shoes level
with the front edge of the roughened side panels.
Press OK, and the meter will measure your
distance on the basis of the heart rate signal.
Measurement takes 6 seconds, and after that
POSIT ION 2 YE S is displayed. Position yourself as
shown in gure Pos 2, the heels of your shoes level
with the rear edge of the roughened side panels.
Press OK, and the meter will measure your distance
on the basis of the heart rate signal. Measurement
takes 6 seconds, and after that SET UP RE ADY is
displayed.
Pos 1 Pos 2
• If the meter cannot receive the heart rate signal
or there are problems in measuring the distance,
the meter will return to the SET UP display. In case
of such an error, the text Hr Err is displayed for
5 seconds.