Manuals / Brands / Computer Equipment / Switch / Tyco / Computer Equipment / Switch

Tyco 1540 Support for Metasys Integration, Support for Crompton Integra operation, Design considerations

1 69

Download 69 pages, 4.88 Mb

Integra 1540, 1000, 0640, 0440, 0340, 0240 Issue 1 04/03

Support for Metasys Integration

Johnson Control Systems

System House, Randalls Research Park,

Randalls Way, Leatherhead,

Surrey, KT22 7TS

England

Support for Crompton Integra operation

This is available via local sales and service centre.

Design considerations

When integrating the Crompton equipment into a Metasys Network, keep the following

considerations in mind.

• Make sure all Crompton equipment is set up, started and running properly before attempting

to integrate with the Metasys Network.

• A maximum of 32 devices can be connected to any one NCM N2 Bus.

Vendor Address 1-247 (Limited by co-resident Modbus protocol)

Port Set-up

Baud Rate 9600

Duplex Full

Word Length 8

Stop Bits 1

Parity None

Interface RS485

Contents

Main Energy Division Page 1 Introduction 2 Display Screens 3 Setting up 4 Specification 5 Basis of measurement and calculations 6 Serial Communications 7. Maintenance 8 Appendix A CE Declaration of Conformity 1 Introduction 1.1 Unit Characteristics 1.1.1 0240 1.1.2 0340 1.1.3 0440 and 0640 1.1.4 1000 1.1.5 1540 1.2 Maximum Power 1.3 Secondary Voltage 1.4 Demand Calculation 1.5 RS485 Serial Option 1.6 Pulse Output Option 1.7 Analogue Output Option 2 Display Screens 2.1 Layout 2.2 Start Up Screens 2.3 System Screen 2.4 System %THD Screen 2.5 Line to Neutral Voltages 2.6 Line to Neutral Voltage %THD 2.7 Line to Line Voltages 2.8 Line to Line Voltages %THD 2.9 Line Currents 2.10 Line Currents %THD 2.11 Neutral Current, Frequency and Power Factor 2.12 Power 2.13 Active Energy (kWh) 2.14 Reactive Energy (kVArh) 2.15 Demand 2.16 Maximum Demand 2.17 Over Range 2.18 kWh and kVArh Display Range 2.19 Error Messages 3 Setting up 3.1 Introduction 3.2 Number Entry Procedure Page Page Page 3.4 Changing the Password 3.5 Full Scale Current 3.6 Potential Transformer Primary Voltage Page 3.7 Potential Transformer Secondary Value 3.8 Demand Integration Time 3.9 Resets 3.10 Pulsed Output, Pulse Duration 3.11 Pulse Rate 3.12 RS485 Baud Rate 3.13 RS485 Parity Selection 3.14 RS485 Modbus Address 3.15 Analogue Output Set Up 3.15.1 Introduction 3.15.1.1 Second Channel 3.15.1.2 Reverse Operation 3.15.1.3 Reduced output range 3.15.2 Analogue Output Scaling Example 3.15.2.1 Reading (A1r or A2r) 3.15.2.2 Reading Top (A1rt or A2rt) 3.15.2.3 Reading Bottom (A1rb or A2rb) 3.15.2.4 Output Page Page Page Page 3.15.5 Parameters available for analogue outputs 3.15.6 Reading (Parameter Selection) - A1r or A2r 3.15.7 Reading Top A1rt or A2rt 3.15.8 Reading Bottom - A1rb or A2rb 3.15.9 Output Top A1ot or A2ot 3.15.10 Output Bottom A1ob or A2ob 4 Specification 4.1 Display Only Versions 4.1.4 Safety 4.1.5 Insulation 4.1.6 Environmental 4.2 Display/Transducer Combined 0240, 0340, 0440, 0640 4.2.1 Inputs 4.2.2 Auxiliary Power Supply 4.2.2.1 High Voltage version 4.2.2.2 Low Voltage version 4.2.3 Measuring Ranges 4.2.4 Accuracy 4.2.5 Reference conditions of influence quantities 4.2.6 EMC Standards 4.2.7 Safety 4.3 Display/Tranducer Combined 1000 and 1540 4.3.1 Inputs 4.3.2 Auxiliary Power Supply 4.3.3 Accuracy 4.3.4 Reference conditions 4.3.5 Reference conditions of influence quantities 4.3.6 Nominal range of use of influence quantities for measurands 4.3.7 Functional ranges 4.3.8 Screen 4.3.9 Standards 4.3.10 Safety 4.3.11 Insulation 4.3.12 Environmental 4.3.13 Enclosure 4.3.14 Serial Communications Option 4.3.15 Active Energy Pulsed Output Option 4.3.16 Integra 1540 Only 5 Basis of measurement and calculations Reactive and Apparent Power Energy resolution Power Factor Maximum Demand Total Harmonic Distortion (1540 only) 6 Serial Communications 6.1. RS485 Port Modbus or JC N2 6.2 Modbus Implementation Input Registers 58 Modbus Holding Registers and Integra set up 6.3 RS485 Implementation of Johnson Controls Metasys Application details Metasys release requirements Support for Metasys Integration Support for Crompton Integra operation Design considerations METASYS N2 application Integra 1560/1580 Point Mapping table 7 Maintenance Warning