Tyco 1540 1.1 Unit Characteristics

1.1 Unit Characteristics

1.1.1 0240

The 0240 will display the following parameters:

• System voltage (average of all phases)

• System frequency (Hz)

• Voltage line to neutral for each phase (4-wire systems only)

• Voltage line to line for each phase (calculated in 4-wire)

The 0240 has Set-up screens for potential transformer primary

and secondary voltages.

1.1.2 0340

The 0340 will display the following parameters:

• System voltage (average of all phases)

• System current (average of all phases)

• Voltage line to neutral for each phase (4-wire systems only)

• Voltage line to line for each phase (calculated in 4-wire)

• Current in each line.

The 0340 has Set-up screens for:

• Full-scale current value

• Potential transformer primary and secondary voltages.

1.1.3 0440 and 0640

The 0440 operates on a mains frequency of 400 Hz nominal

and the 0640 at 45-65 Hz. The units can measure and display

the following parameters:

• System voltage (average of all phases)

• System current (average of all phases)

• System frequency (Hz)

• Voltage line to neutral for each phase (4-wire systems only)

• Voltage line to line for each phase (calculated in 4-wire)

• Current in each line

The 0440 and 0640 have Set-up screens for:

• Full-scale current value

• Potential transformer primary and secondary voltages.

6Integra 1540, 1000, 0640, 0440, 0340, 0240 Issue 1 04/03

Default display

Default display

Default display

Contents

Main Energy Division Page 1 Introduction 2 Display Screens 3 Setting up 4 Specification 5 Basis of measurement and calculations 6 Serial Communications 7. Maintenance 8 Appendix A CE Declaration of Conformity 1 Introduction 1.1 Unit Characteristics 1.1.1 0240 1.1.2 0340 1.1.3 0440 and 0640 1.1.4 1000 1.1.5 1540 1.2 Maximum Power 1.3 Secondary Voltage 1.4 Demand Calculation 1.5 RS485 Serial Option 1.6 Pulse Output Option 1.7 Analogue Output Option 2 Display Screens 2.1 Layout 2.2 Start Up Screens 2.3 System Screen 2.4 System %THD Screen 2.5 Line to Neutral Voltages 2.6 Line to Neutral Voltage %THD 2.7 Line to Line Voltages 2.8 Line to Line Voltages %THD 2.9 Line Currents 2.10 Line Currents %THD 2.11 Neutral Current, Frequency and Power Factor 2.12 Power 2.13 Active Energy (kWh) 2.14 Reactive Energy (kVArh) 2.15 Demand 2.16 Maximum Demand 2.17 Over Range 2.18 kWh and kVArh Display Range 2.19 Error Messages 3 Setting up 3.1 Introduction 3.2 Number Entry Procedure Page Page Page 3.4 Changing the Password 3.5 Full Scale Current 3.6 Potential Transformer Primary Voltage Page 3.7 Potential Transformer Secondary Value 3.8 Demand Integration Time 3.9 Resets 3.10 Pulsed Output, Pulse Duration 3.11 Pulse Rate 3.12 RS485 Baud Rate 3.13 RS485 Parity Selection 3.14 RS485 Modbus Address 3.15 Analogue Output Set Up 3.15.1 Introduction 3.15.1.1 Second Channel 3.15.1.2 Reverse Operation 3.15.1.3 Reduced output range 3.15.2 Analogue Output Scaling Example 3.15.2.1 Reading (A1r or A2r) 3.15.2.2 Reading Top (A1rt or A2rt) 3.15.2.3 Reading Bottom (A1rb or A2rb) 3.15.2.4 Output Page Page Page Page 3.15.5 Parameters available for analogue outputs 3.15.6 Reading (Parameter Selection) - A1r or A2r 3.15.7 Reading Top A1rt or A2rt 3.15.8 Reading Bottom - A1rb or A2rb 3.15.9 Output Top A1ot or A2ot 3.15.10 Output Bottom A1ob or A2ob 4 Specification 4.1 Display Only Versions 4.1.4 Safety 4.1.5 Insulation 4.1.6 Environmental 4.2 Display/Transducer Combined 0240, 0340, 0440, 0640 4.2.1 Inputs 4.2.2 Auxiliary Power Supply 4.2.2.1 High Voltage version 4.2.2.2 Low Voltage version 4.2.3 Measuring Ranges 4.2.4 Accuracy 4.2.5 Reference conditions of influence quantities 4.2.6 EMC Standards 4.2.7 Safety 4.3 Display/Tranducer Combined 1000 and 1540 4.3.1 Inputs 4.3.2 Auxiliary Power Supply 4.3.3 Accuracy 4.3.4 Reference conditions 4.3.5 Reference conditions of influence quantities 4.3.6 Nominal range of use of influence quantities for measurands 4.3.7 Functional ranges 4.3.8 Screen 4.3.9 Standards 4.3.10 Safety 4.3.11 Insulation 4.3.12 Environmental 4.3.13 Enclosure 4.3.14 Serial Communications Option 4.3.15 Active Energy Pulsed Output Option 4.3.16 Integra 1540 Only 5 Basis of measurement and calculations Reactive and Apparent Power Energy resolution Power Factor Maximum Demand Total Harmonic Distortion (1540 only) 6 Serial Communications 6.1. RS485 Port Modbus or JC N2 6.2 Modbus Implementation Input Registers 58 Modbus Holding Registers and Integra set up 6.3 RS485 Implementation of Johnson Controls Metasys Application details Metasys release requirements Support for Metasys Integration Support for Crompton Integra operation Design considerations METASYS N2 application Integra 1560/1580 Point Mapping table 7 Maintenance Warning