U-Line manual Wood Trim Finishing, Staining and final finish application, 2175BEVS, 2175BEVOL

Wood Trim Finishing

The U-Line Beverage Center is equipped with wood- trimmed wine racks that are coated at the factory with a clear vinyl sealer, which will adequately protect the wood in normal usage. A final finish coat was not applied so that the wood trim could be stained to match décor. The trim on the racks may be coated with a final finish or stained.

To remove the wood trim surrounding the controller:

2	3
	1
	4
	ULIN_0836_A

Figure 18

1.Loosen the two screws holding the controller to the mounting bracket (Figure 18, 1).

2.Lift the controller housing (Figure 18, 4) and then rotate forward to expose the wiring harness on the back.

3.Disconnect the wiring harness from the controller (Figure 18, 3).

4.Remove the two screws holding in the controller housing (Figure 18, 2), then remove from wood.

NOTE: Carefully remove controller from housing. The glass front is not secured to the controller. Glass may fall and break, which is not covered under warranty.

5. After staining, installation is the reverse.

Be sure to align glass with controller when installing, otherwise controller may not work correctly.

WARNING

To prevent permanent damage to the inner liner of your unit, the wood trim MUST be removed from the unit for staining and/or finishing. Allow stain/finish to dry thoroughly (at least 24 hours per coat) in accordance with the product manufacturer’s instructions prior to reinstallation. Failure to do so may cause the inner liner of the unit to have a permanent odor, which is not covered by the warranty.

If staining the trim is desired, it must be done before the application of any type of final finish. Review the following staining/final finish and final finish-only guidelines when staining/ and or sealing the wood to ensure proper adhesion and durability of the finish.

NOTE: Glass in door is tinted. Stain may look darker when door is closed.

Staining and final finish application:

1.Remove all screws securing wood trim to interior components, and remove the trim from the cabinet interior.

IMPORTANT

DO NOT use oil-based stains on wood trim. Vapors from oil-based stains will permanently penetrate the liner and will not dissipate over time.

2.Apply Minwax® Water-Based Wood Stain to wood with a synthetic bristle brush or a foam applicator. Allow stain to penetrate approximately three minutes. Before the stain is dry, take a stain dampened rag and remove any excess stain remaining. Wipe in the direction of the grain with medium pressure to achieve the desired stain color.

3.After two hours, repeat step 2. This will even out the color of the wood.

4.Allow stain to dry for a minimum of three hours before applying the final finish.

5.If desired, sand the wood with very fine sandpaper to smooth the surface after the staining process.

6.Remove all dust from the wood, and apply one coat of Minwax® Polycrylic® Protective Finish using a synthetic bristle brush to the wood. This finish should be applied in a thin coat following the direction of the grain.

Apply the finish to the back and sides of the wood first, and allow it to dry for two hours. Apply the finish to the front side of the wood next, and allow it to dry for two hours. Sand with very fine 220 grit sandpaper. Apply two addition coats of the finish in the same manner, but do not sand the trim after the final third coat is applied.

7.Allow the final coat to dry for 24 hours before reinstalling the trim to the cabinet interior components.

Final finish-only application:

1.Remove all screws securing wood trim to interior components, and remove the trim.

2.Lightly scruff sand the wood trim with 280 or finer grit sandpaper.

3.Remove sanding dust with a clean, dry cloth.

4.The factory-applied seal is compatible with virtually all finishes. A low odor, water clean up, quick-drying finish such as Minwax® Polycrylic® Protective Finish is recommended (Minwax® Polycrylic® is an ultra fast- drying water-based finish). Apply a thin coat of a clear, protective finish, following the container label directions.

5.Lightly sand and reapply if desired.

6.Allow the final coat to dry for 24 hours before reinstalling the trim to the cabinet interior components.

2175BEVS, 2175BEVOL 17