United States Stove C242 Installation, Minimum Clearance To Combustible Walls US , Canada

Installation

Place the heater on solid masonry or solid concrete. When the heater is used on a combustible floor, use an Underwrit- ers Listed floor protector. The floor protector must comply with UL Standards(USA) and CAN/ULC S627(Canada).The base should extend at least 16" beyond the door of the heater and should extend under the flue pipe if it is elbowed towards a wall

(Fig. 5).

MINIMUM CLEARANCE

TO COMBUSTIBLE WALLS

US , CANADA

18"

458mm

(60" MIN.)

1.	Uncrate and/or unpack the heater, removing all pack-
	ing material, being careful not to dispose of the Parts
	Bag.
2.	Open the front feed door and remove the parts from
	inside the stove. You should find the following: Hearth
	Plate (1); Solid Damper (1); Lids (2); Pivoting Top (1);
	Lid Support (1); Parts Package (1) containg nuts,
	bolts, door handle, door latch and securing harware;
	Legs (4); Cast Iron Collar (1); Cast Iron Damper (1);
	Baffle Assembly (1); Lid Lifter (1).
3.	Place cardboard or other soft material adjacent to the

37-1/2" 953mm

34" 865mm

28"	FIG. 2
	FLOOR
712mm	PROTECTOR

28"

712mm

26"

660mm

FIG. 3	20"
FLOOR
	508mm
PROTECTOR

	stove and carefully turn the stove onto its top side
	(bottom facing up).
4.	Attach hearth plate to the front of the stove in its proper
	location.
5.	Attach both rear and front legs to the stove. Tighten
	the nuts and bolts securely. The stove may now be
	CAREFULLY turned over to stand on its four legs.
6.	Attach the baffle assembly and flue collar to the stove
	by inserting the baffle studs thru the two holes located
	on the top of the rear of the stove; place the flue collar
	over the studs and mount using the proper nuts and
	washers. Place lid support and lid in position on
	pivoting top. Place the slide damper in position on the
	top of the hearth plate and under the feed door, and
	secure with screw in slot.
7.	After consulting the installation instructions for mini-
	mum clearances to combustibles, locate your floor
	protector accordingly and carefully place the stove in
	your selected location. Install stove pipe, elbows and
	thimble as necessary, utilizing either a recently cleaned
	and inspected masonry chimney (properly lined) or a
	UL/ULC Listed chimney. Insure that the damper
	provided is installed in the flue collar.
8.	Again, check the following illustrations and be sure
	you have the clearances shown from the heater and
	the connector pipe to combustible surfaces. If you
	have a solid brick or stone wall behind your heater,
	you may place your heater as close as you wish to the
	wall. However, if the wall is only faced with brick or
	stone, consider it a combustible wall.
9.	If your chimney drafts excessively, purchase and use
	a Barometric Draft Regulator (DR6 available from
	factory).
10.	The chimney connection should be as short as pos-
	sible, and the heater must have its own flue. Do not
	connect this unit to a chimney flue serving other
	appliances.
11.	Use three sheet metal screws in each stove pipe and
	or elbow joint to firmly hold the pipe together.
12.	Do not install this heater in a mobile home or trailer.
13.	Check your local building and insurance codes. The
	installation must comply with their rulings.

HEATER/FLOOR PROTECTOR LOCATION

(Dimensions are required for non-protected surfaces. See chart for dimensions for protected surfaces.)

BACK WALL

DASHED LINES	NON- COMBUSTIBLE
SHOW STRAIGHT	CONSTRUCTION IN
OUT CHIMNEY	ACCORDANCE WITH
CONNECTOR	NFPA 211 or CAN/CSA
34"	B365-M91	26"
865mm		660mm 28-3/4"
6"		730mm
153mm
60"
		FLOOR
		PROTECTOR
16"
407mm		FIG. 4
6"		6"
153mm	28"	153mm
	204mm

Protected Surfaces (NFPA 211)

Parallel		Corner
Side	Rear
12-inches	12-inches	12-inches
305-mm	305-mm	305-mm

CAUTION!

KEEP FURNISHINGS AND OTHER

COMBUSTIBLE MATERIALS

AWAY FROM THE HEATER.

4