Enterasys Networks VHSIM2-A6DP

Installing a VHSIM

2-12 Installation

7. Place the VHSIM2-A6DP behind the device faceplate as shown back in Figure2-6.

8. Insert the connectors of the VHSIM2-A6DP into the host device connector pins on the device.

9. Press down firmly on the back of the VHSIM2-A6DP until the pins slide all the way into the

connector holes.

10. Secure the VHSIM2-A6DP to the faceplate usi ng the screws saved in step 5.

11. Secure the VHSIM2-A6DP to the standoffs using the screws saved in step6.

12. Reattach the chassis cover to the device, reconnect the power cord, and reconn ect the de vice to

your network.

13. Refer to Chapter3 for instructions on configuring the VHSIM2-A6DP using Local

Management.

CAUTION: In step8, ensure tha t the standoffs on the device align with the standoff

screw holes on the VHSIM2-A6DP to prevent bending the pins.

ELECTRICAL HAZARD: Ensure that the chassis cover is in place before reconnecting

the power cord.

Contents

Main Page i NOTICE ELECTRICAL HAZARD: Only qualified person nel should perform installation procedures. ii FCC NOTICE INDUSTRY CANADA NOTICE VCCI NOTICE iii ENTERASYS NETWORKS, INC. PROGRAM LICENSE AGREEMENT iv Page vi DECLARATION OF CONFORMITY Contents vii Contents ABOUT THIS GUIDE 1 2 3 viii Contents Contents ix 4 A INDEX B xFigures Figures Page Page About This Guide WHO SHOULD USE THIS GUIDE STRUCTURE OF THIS GUIDE RELATED MANUALS Related Manuals xv DOCUMENT CONVENTIONS The following conventions are used throughout this document: Page Introduction 1.1 OVERVIEW Page 1.2 GETTING HELP Page Installation 2.1 UNPACKING THE VHSIM2-A6DP 2.2 INSTALLING APIMs Page Installing APIMs 2-4 Installation 4. Align the APIM connector with the VHSIM2-A6DP connector pins as shown in Figure2-2. 2.3 INSTALLING VAPIMs Page Installing VAPIMs Installation 2-7 4. Align the VAPIM connectors into the VHSIM2-A6DP connectors as shown in Figure2-4. 2.4 INSTALLING A VHSIM 2.4.1 Installing a VHSIM2-A6DP in an Interface Module Page Installing a VHSIM 2-10 Installation Place the VHSIM behind the module faceplate. See Figure2-6. 2.4.2 Installing a VHSIM2-A6DP in a Standalone Device Page Local Management 3.1 USING LOCAL MANAGEMENT SCREENS 3.1.1 Local Management Screen Elements Using Local Management Screens Local Management 3-3 Figure 3-1 Example of a Local Management Screen NOTE: Only the password, configuration and status screens have event message fields. Page 3.1.2 Local Management Keyboard Conventions Using Local Management Screens 3-6 Local Management 3.1.3 Navigating Local Management Screens Figure 3-2 VHSIM2-A6DP Local Management Screen Hierarchy 3.1.3.1 Selecting Local Management Menu Screen Items 3.1.3.2 Exiting Local Management Screens 3.2 ACCESSING THE VHSIM2-A6DP ATM SCREEN Page 3.3 ATM CONNECTIONS SCREEN ATM Connection Setup Screen Local Management 3-11 3.4 ATM CONNECTION SETUP SCREEN Figure 3-5 ATM Connection Setup Screen Page Page 3.5 TRAFFIC MANAGEMENT PVC PRIORITY ASSIGNMENTS Page Page 3.5.1 Adding Traffic Management PVC Priority Assignments Page 3.5.2 Modifying an Entry (Vport) 3.5.3 Deleting an Entry (Vport) 3.5.4 Traffic Management PVC Priority Assignments Screen Example 3.6 ADD/DELETE ENTRY SCREEN 3.6.1 Adding an Entry (PVC) 3.6.2 Modifying an Entry (PVC) 3.6.3 Deleting an Entry (PVC) 3.7 ATM CONNECTION SETUP BY VIRTUAL INTERFACE SCREEN Page 3.7.1 Selecting a Virtual Interface 3.8 PHYSICAL PORT CONFIGURATION MENU SCREEN 3.9 PORT FRAMER CONFIGURATION SCREEN Page 3.9.1 Configuring an APIM 3.10 ATM PORT REDUNDANCY CONFIGURATION SCREEN Page Page 3.10.1 Setting the Redundancy Status 3.10.2 Setting the Primary Port 3.10.3 Setting the Active Port 3.10.4 Setting the Activation of Redundant Port Field 3.10.5 Setting the Revert to Primary Port Field 3.10.6 Setting the Periodic Test Status Field 3.10.7 Setting the Periodic Test Time 3.10.8 Using the TEST PORTS NOW Command 3.10.9 Using the RESET TO FACTORY DEFAULTS Command 3.11 LAN EMULATION CLIENTS SCREEN Page 3.12 LEC TABLE SCREEN Page 3.13 LEC ADMINISTRATION SCREEN Page Page Page 3.13.1 Changing the LEC Status of an Existing LEC 3.13.2 Configuring a New LEC Automatically 3.13.3 Configuring a New LEC Manually Page 3.13.4 Modifying an Existing LEC 3.13.5 Deleting an Existing LEC 3.14 LEC PROPERTIES SCREEN Page Page 3.14.1 Viewing Multiple ELANs 3.15 LEC ARP CACHE SCREEN Page 3.15.1 Performing a Search 3.16 LEC PRIORITY QUEUES SCREEN Page 3.16.1 Assigning Priorities to a LEC 3.17 SIGNALLING SCREEN Page 3.17.1 Changing the UNI Version 3.17.2 Changing the ILMI Status to Disabled 3.17.3 Changing the UNI Status 3.17.4 Restarting UNI 3.17.5 Restarting the ILMI 3.18 TRAFFIC MANAGEMENT SCREEN Page 3.18.1 Setting up a Descriptor Profile 3.18.2 Modifying a Descriptor Profile 3.18.3 Deleting a Descriptor Profile 3.19 DISCOVERY ELAN SETUP SCREEN Page 3.19.1 Assigning the VHSIM2-A6DP to a Discovery ELAN LANVIEW LEDs 4-1 LANVIEW LEDs 4.1 VHSIM2-A6DP LEDs Refer to Tabl e 4-1 and Tab le 4-2 for a description of VHSIM2-A6DP and APIM/VAPIM LEDs. Page A VHSIM2-A6DP Specifications A.1 SPECIFICATIONS Page B APIM and VAPIM Specifications B.1 APIM-21 SPECIFICATIONS B.2 APIM-29 SPECIFICATIONS B.3 APIM-29LR SPECIFICATIONS B.4 APIM-22 SPECIFICATIONS B.5 APIM-67 SPECIFICATIONS Page B.6 VAPIM-31 SPECIFICATIONS B.7 VAPIM-39 SPECIFICATIONS B.8 VAPIM-39LR SPECIFICATIONS Page Index-1 Index A D E F K L N O R U V