Enterasys Networks VHSIM2-A6DP 3.6 ADD/DELETE ENTRY SCREEN

Add/Delete Entry Screen

Local Management 3-21

3.6 ADD/DELETE ENTRY SCREEN

The Add/Delete Entry screen is used to create, modify, or delete PVCs.

To access the Add/Delete Entry screen from the ATM Connection Setup screen perform the

following steps:

1. Use the arrow keys to highlight the ADD/DELETE command at the bottom of the ATM

Connection Setup screen.

2. Press ENTER, the Add/Delete Entry screen, Figure3-8, displays.

Figure 3-8 Add/Delete Entry Screen

The following list explains each Add/Delete Entry screen field:

VPI (Modifiable)

Used to enter the Virtual Path Identifier of the PVC. The available range for this field is 0 or 1,

with a default value of 0.

VCI (Modifiable)

Used to enter the Virtual Channel Identifier of the PVC. The available range for this field is 32

through 1019.

NOTE: The Add/Delete Entry screen will display only if the host device has been set

to operate as a SecureFast switch with the VHSIM2-A6DP installed. Refer to the Local

Management chapter of the host device for instructions on configuring the host device

for this type of operation.

RETURN

VPI VCI AAL Type Encapsulation Type

0 0 [ 5 ] [VC Mux 802.3 Bdg]

EXITADD/MODIFY

2825 13

Contents

Main Page i NOTICE ELECTRICAL HAZARD: Only qualified person nel should perform installation procedures. ii FCC NOTICE INDUSTRY CANADA NOTICE VCCI NOTICE iii ENTERASYS NETWORKS, INC. PROGRAM LICENSE AGREEMENT iv Page vi DECLARATION OF CONFORMITY Contents vii Contents ABOUT THIS GUIDE 1 2 3 viii Contents Contents ix 4 A INDEX B xFigures Figures Page Page About This Guide WHO SHOULD USE THIS GUIDE STRUCTURE OF THIS GUIDE RELATED MANUALS Related Manuals xv DOCUMENT CONVENTIONS The following conventions are used throughout this document: Page Introduction 1.1 OVERVIEW Page 1.2 GETTING HELP Page Installation 2.1 UNPACKING THE VHSIM2-A6DP 2.2 INSTALLING APIMs Page Installing APIMs 2-4 Installation 4. Align the APIM connector with the VHSIM2-A6DP connector pins as shown in Figure2-2. 2.3 INSTALLING VAPIMs Page Installing VAPIMs Installation 2-7 4. Align the VAPIM connectors into the VHSIM2-A6DP connectors as shown in Figure2-4. 2.4 INSTALLING A VHSIM 2.4.1 Installing a VHSIM2-A6DP in an Interface Module Page Installing a VHSIM 2-10 Installation Place the VHSIM behind the module faceplate. See Figure2-6. 2.4.2 Installing a VHSIM2-A6DP in a Standalone Device Page Local Management 3.1 USING LOCAL MANAGEMENT SCREENS 3.1.1 Local Management Screen Elements Using Local Management Screens Local Management 3-3 Figure 3-1 Example of a Local Management Screen NOTE: Only the password, configuration and status screens have event message fields. Page 3.1.2 Local Management Keyboard Conventions Using Local Management Screens 3-6 Local Management 3.1.3 Navigating Local Management Screens Figure 3-2 VHSIM2-A6DP Local Management Screen Hierarchy 3.1.3.1 Selecting Local Management Menu Screen Items 3.1.3.2 Exiting Local Management Screens 3.2 ACCESSING THE VHSIM2-A6DP ATM SCREEN Page 3.3 ATM CONNECTIONS SCREEN ATM Connection Setup Screen Local Management 3-11 3.4 ATM CONNECTION SETUP SCREEN Figure 3-5 ATM Connection Setup Screen Page Page 3.5 TRAFFIC MANAGEMENT PVC PRIORITY ASSIGNMENTS Page Page 3.5.1 Adding Traffic Management PVC Priority Assignments Page 3.5.2 Modifying an Entry (Vport) 3.5.3 Deleting an Entry (Vport) 3.5.4 Traffic Management PVC Priority Assignments Screen Example 3.6 ADD/DELETE ENTRY SCREEN 3.6.1 Adding an Entry (PVC) 3.6.2 Modifying an Entry (PVC) 3.6.3 Deleting an Entry (PVC) 3.7 ATM CONNECTION SETUP BY VIRTUAL INTERFACE SCREEN Page 3.7.1 Selecting a Virtual Interface 3.8 PHYSICAL PORT CONFIGURATION MENU SCREEN 3.9 PORT FRAMER CONFIGURATION SCREEN Page 3.9.1 Configuring an APIM 3.10 ATM PORT REDUNDANCY CONFIGURATION SCREEN Page Page 3.10.1 Setting the Redundancy Status 3.10.2 Setting the Primary Port 3.10.3 Setting the Active Port 3.10.4 Setting the Activation of Redundant Port Field 3.10.5 Setting the Revert to Primary Port Field 3.10.6 Setting the Periodic Test Status Field 3.10.7 Setting the Periodic Test Time 3.10.8 Using the TEST PORTS NOW Command 3.10.9 Using the RESET TO FACTORY DEFAULTS Command 3.11 LAN EMULATION CLIENTS SCREEN Page 3.12 LEC TABLE SCREEN Page 3.13 LEC ADMINISTRATION SCREEN Page Page Page 3.13.1 Changing the LEC Status of an Existing LEC 3.13.2 Configuring a New LEC Automatically 3.13.3 Configuring a New LEC Manually Page 3.13.4 Modifying an Existing LEC 3.13.5 Deleting an Existing LEC 3.14 LEC PROPERTIES SCREEN Page Page 3.14.1 Viewing Multiple ELANs 3.15 LEC ARP CACHE SCREEN Page 3.15.1 Performing a Search 3.16 LEC PRIORITY QUEUES SCREEN Page 3.16.1 Assigning Priorities to a LEC 3.17 SIGNALLING SCREEN Page 3.17.1 Changing the UNI Version 3.17.2 Changing the ILMI Status to Disabled 3.17.3 Changing the UNI Status 3.17.4 Restarting UNI 3.17.5 Restarting the ILMI 3.18 TRAFFIC MANAGEMENT SCREEN Page 3.18.1 Setting up a Descriptor Profile 3.18.2 Modifying a Descriptor Profile 3.18.3 Deleting a Descriptor Profile 3.19 DISCOVERY ELAN SETUP SCREEN Page 3.19.1 Assigning the VHSIM2-A6DP to a Discovery ELAN LANVIEW LEDs 4-1 LANVIEW LEDs 4.1 VHSIM2-A6DP LEDs Refer to Tabl e 4-1 and Tab le 4-2 for a description of VHSIM2-A6DP and APIM/VAPIM LEDs. Page A VHSIM2-A6DP Specifications A.1 SPECIFICATIONS Page B APIM and VAPIM Specifications B.1 APIM-21 SPECIFICATIONS B.2 APIM-29 SPECIFICATIONS B.3 APIM-29LR SPECIFICATIONS B.4 APIM-22 SPECIFICATIONS B.5 APIM-67 SPECIFICATIONS Page B.6 VAPIM-31 SPECIFICATIONS B.7 VAPIM-39 SPECIFICATIONS B.8 VAPIM-39LR SPECIFICATIONS Page Index-1 Index A D E F K L N O R U V