Manuals / Enterasys Networks / Computer Equipment / Network Card

Enterasys Networks VHSIM2-A6DP manual Port Framer Configuration Screen, Physical Port Toggle

Models: VHSIM2-A6DP

1 118

Download 118 pages 61.27 Kb

Page 62

Port Framer Configuration Screen

3.9PORT FRAMER CONFIGURATION SCREEN

The Port Framer Configuration screen is used to enable or disable ATM statistics and alarms, and to specify, if applicable, the transmission type that the APIM will use (SONET or SDH). The Port Framer Configuration screen allows these configurations to be performed on both the primary and redundant APIMs.

To access the Port Framer Configuration screen, perform the following steps:

1.Use the arrow keys to highlight the PORT FRAMER CONFIGURATION menu item from the Physical Port Configuration Menu screen.

2.Press ENTER. The Port Framer Configuration screen, Figure 3-11, displays.

Figure 3-11 Port Framer Configuration Screen

	Physical Port:	[1]
	ATM Port Type: ATM IF: 155Mbps, SONET/SDH, OC-3, MMF, SC
	Statistics:	[ OFF ]
	Alarms:	[ OFF ]
	Idle Cells:	[ UNASSIGNED ]
Cell Payload Scrambling:		[ ON ]
	Transmission Type:	[ SONET ]
SAVE	EXIT	RETURN

28251_16

The following list explains each of the Port Framer Configuration screen fields.

Physical Port (Toggle)

This field is used to select which APIM to be configured. This field toggles between 1 (APIM 1) and 2 (APIM 2).

3-28Local Management

Image 62

Enterasys Networks VHSIM2-A6DP manual Port Framer Configuration Screen, Physical Port Toggle

Contents

VHSIM2-A6DP User’s Guide Page Page FCC Notice Enterasys NETWORKS, INC Program License Agreement Page Page Declaration of Conformity Contents Viii Contents Lanview Leds Figures VAPIM-31 VAPIM-39 VAPIM-39LR Tables WHO should USE this Guide Structure of this GuideRelated Manuals ATM Technology Guide Cabling GuideDocument Conventions Xvi Introduction OverviewMIB Support Lanview Diagnostic LEDsATM Port Interface Modules APIMs and VAPIMs Getting Help Your email addressPage Installation Unpacking the VHSIM2-A6DPInstalling APIMs Removing the Apim Coverplate Installing an Apim Apim Screws Optional Third Installing VAPIMs 6Installation Installing a Vapim Vapim Screws Optional Third Installing a Vhsim Installing a VHSIM2-A6DP in an Interface ModuleRemoving the Vhsim Coverplate Place the Vhsim behind the module faceplate. See Figure Installing a VHSIM2-A6DP in a Standalone Device 12Installation Local Management Using Local Management Screens Local Management Screen ElementsEvent Message Field Display FieldInput Fields Command FieldsDisplay Fields Selection/Toggle FieldsLocal Management Keyboard Conventions Navigating Local Management Screens Selecting Local Management Menu Screen ItemsExiting Local Management Screens Using the Exit CommandUsing the Return Command Accessing the VHSIM2-A6DP ATM Screen ConnectionsPhysical Port Configuration ATM Connections Screen Connection TableATM Connection Setup Screen Connections by Virtual InterfaceEncapsulation Type Read-Only Total Bandwidth Available Read-OnlyATM Port Current Connections Read-Only ATM Address ESI Read-Only ADD/DELETE CommandPrevious Command Traffic Category Read-OnlyTraffic Management PVC Priority Assignments Traffic Management PVC Priority Assignments ScreenAAL Type Read-Only PVC Vport ModifiableNumber of Virtual Queues Modifiable Encapsulation Type ToggleProfile Index Modifiable Profile Name Read-OnlyAdding Traffic Management PVC Priority Assignments 18Local Management Modifying an Entry Vport Deleting an Entry VportTraffic Management PVC Priority Assignments Screen Example Example Traffic Management PVC Priority Assignments ScreenADD/DELETE Entry Screen Add/Delete Entry ScreenTraffic Profile Index Selectable ADD/MODIFY CommandAdding an Entry PVC Modifying an Entry PVC Deleting an Entry PVCATM Connection Setup by Virtual Interface Screen Total Bandwidth Allocated Read-OnlyVirtual Interface # Selectable Application Port # Read-onlyPrev Command Selecting a Virtual InterfacePhysical Port Configuration Menu Screen Port Framer ConfigurationPort Framer Configuration Screen Physical Port ToggleIdle Cells Toggle ATM Port Type Read-OnlyStatistics Toggle Cell Payload Scrambling ToggleConfiguring an Apim ATM Port Redundancy Configuration Screen12 ATM Port Redundancy Configuration Screen Redundancy Status ToggleActivation of redundant port Toggle Primary Port ModifiableActive Port Modifiable Revert to Primary port ToggleTest Ports NOW Command Setting the Redundancy StatusSetting the Primary Port Reset to Factory Defaults CommandSetting the Revert to Primary Port Field Setting the Active PortSetting the Activation of Redundant Port Field Setting the Periodic Test Status Field Setting the Periodic Test TimeLAN Emulation Clients Screen Using the Test Ports NOW CommandUsing the Reset to Factory Defaults Command LEC Table LEC Table Screen LEC Transmit QueuesElan ID Read-Only LEC ID Read-OnlyVer Read-Only Elan Name Read-OnlyLEC Administration Screen 15 LEC Administration ScreenSelective Multicast Toggle Configure LEC ToggleMTU Size Toggle LLC Multiplex Capable ToggleLEC Status Toggle LES ATM Address ModifiableLEC Index Read-Only/Modifiable Lane Version ToggleCreate Mode Command ADD LEC CommandModify Mode Command Lecs ATM Address ModifiableConfiguring a New LEC Automatically Changing the LEC Status of an Existing LECConfiguring a New LEC Manually 46Local Management Modifying an Existing LEC Deleting an Existing LEC LEC Properties ScreenLEC Index Selectable Actual Elan Name Read-OnlyLecs ATM Addr Read-Only Lane Version Read-OnlyLEC ATM Addr Read-Only LES ATM Addr Read-OnlyViewing Multiple ELANs LEC ARP Cache Screen 17 LEC ARP Cache Screen# Selectable Search By SelectableMAC Address Read-Only ATM Address Read-OnlyLEC Priority Queues Screen Search CommandPerforming a Search Number of Virtual Queues Selectable 18 Traffic Managment LEC Priority Queues ScreenAssigning Priorities to a LEC Profile Index SelectableIlmi State Read-Only Signalling ScreenIlmi Status Selectable Ilmi Physical ATM Address Read-Only Restart UNI CommandRestart Ilmi Command UNI Status ToggleChanging the Ilmi Status to Disabled Changing the UNI VersionRestarting the Ilmi Changing the UNI StatusRestarting UNI Traffic Management Screen Profile Name SelectableTraffic Parameters Peak Cell Rate PCR Selectable Traffic Category SelectableTraffic Parameters Transmit Units Selectable Sustained Cell Rate SCR SelectableDeleting a Descriptor Profile Setting up a Descriptor ProfileModifying a Descriptor Profile Discovery Elan Setup Screen Mode Toggle Status ToggleAssigning the VHSIM2-A6DP to a Discovery Elan Lanview LEDs VHSIM2-A6DP LEDsFlashing Regulatory Compliance SpecificationsEnvironment Page Apim and Vapim Specifications APIM-21 SpecificationsAPIM-29 Specifications Figure B-2 APIM-29APIM-29LR Specifications Figure B-3 APIM-29LRAPIM-22 Specifications STS3APIM-67 Specifications BNC6APIM and Vapim Specifications VAPIM-31 Specifications Figure B-7 VAPIM-31VAPIM-39 Specifications Figure B-8 VAPIM-39VAPIM-39LR Specifications Figure B-9 VAPIM-39LRPage Index Index-2 Index-3