The TV will automatically enter the standby mode if no
operations are performed during the time span you set
(“30min.” or “3hr.”).
• Five minutes before the TV enters standby mode, the
remaining time displays every minute.
When set to “Yes” the TV activates the following power
saving mode.
• OPC set to “On” (Page 24)
• Standby Mode set to “Mode 2” (Page 32)
• No Signal Off set to “Enable” (Page 25)
• No Operation Off set to “3hr.” (Page 26)
Allows you to set a time when the TV automatically
switches to standby.
NOTE
• Select “Off” to cancel the sleep timer.
• When the time has been set, countdown automatically
starts.
• Five minutes before the preset of time expires, the
remaining time displays each minute.

No Operation Off

Power Control

Ecology

Power Control

Sleep Timer

Power Control
Basic adjustment

Channel Settings

Auto Installation

Auto Installation

Setup
The TV automatically detects and stores all available
services in your area. This function also allows you to
perform the channel setting for “Digital” and “Analogue”
individually and reconfigure the settings after the initial
auto installation has been completed.
After selecting “Yes” on the screen, you can set
language and channel search the same as in the
initial auto installation. Follow steps 2, 4 and 5
on page 9.
NOTE
• You cannot set the country setting in “Auto Installation”
in the Setup menu. If you want to reconfigure the country
setting, automatically execute initial auto installation after
executing “Reset” from the Setup menu.
• The current country setting is displayed on the screen.
1

Digital channel settings

Programme Setup

Setup

Digital Setting

You can reconfigure DTV services settings
automatically or manually.

E Additional Search

Use this menu to add new services automatically after
auto installation has been completed.

E Manual Search

Add new services within a specified frequency band.
• Enter the frequency using 0 - 9 numeric buttons.

E Manual Adjust

Configure various settings for each service using the
Colour (R, G, Y, B) buttons.
MENU [Setup ... Programme Setup ... Digital Setting ... Manual Adjust]
DTV 993
Service
No.
Old
LCN
EPG
Skip
CH
Skip
Lock
Service
Name
SIT 3
DTV 994 ✔ ✔ SIT 2
DTV 995 ✔ SIT 1
DTV 996 Monosco 576-2
DTV 997 Monosco 576-1
DTV 998 Color Bar 576i
DTV 999 HD Monosco
: Lock
R : CH Skip
G : EPG Skip
Y : Sort
B
Press a/b to select the desired service.
Press the colour button on the remote control
corresponding with the item you want to
reconfigure.
• The ✔ mark indicates the operation is set to on. Each
time the colour button is pressed, you can switch the
corresponding operation on/off.
1
2
Buttons for Manual Adjust operation
Lock: Press R button.
When the service is locked, you must enter your PIN
whenever you tune to the service.
CH Skip: Press G button.
Services with a ✔ mark are passed over when
pressing Pr/s in the TV/remote control unit.
EPG Skip: Press Y button.
Services with a ✔ mark are passed over in the
Electronic Programme Guide (EPG).
Sort: Press B button.
The item position of services can be sorted.
1 Press a/b to select the service whose item
position you want to move, and then press OK.
DTV 994 ✔ ✔ SIT 2
DTV 995 ✔ SIT 1
2 Press a/b to move it to the desired position,
and then press OK.
DTV 994
✔✔
SIT 1
DTV 995
✔
SIT 2
3 Repeat steps 1 and 2 until all desired service
items are sorted.
26
LC-3237X20E-gb.indd 26LC-3237X20E-gb.indd 26 2007/08/31 16:58:352007/08/31 16:58:35