20
TROUBLESHOOTING
TROUBLESHOOTING
Continued
OBSERVED PROBLEM | POSSIBLE CAUSE | REMEDY | ||
ODS/pilot lights but flame goes out when | 1. | Control knob not fully pressed in | 1. | Press in control knob fully |
control knob is released | 2. | Control knob not pressed in long enough | 2. | After ODS/pilot lights, keep control |
|
|
|
| knob pressed in 30 seconds |
| 3. | Equipment shutoff valve not fully open | 3. | Fully open equipment shutoff valve |
| 4. | Thermocouple connection loose at con- | 4. | Hand tighten until snug, then tighten 1/4 |
|
| trol valve |
| turn more |
| 5. | Pilot flame not touching thermocouple, | 5. | A) Contact local natural or propane/LP |
|
| which allows thermocouple to cool, |
| gas company |
|
| causing pilot flame to go out. This prob- |
| B) Clean ODS/pilot (see Cleaning and |
|
| lem could be caused by one or both of |
| Maintenance, page 17) or replace ODS/ |
|
| the following: |
| pilot assembly |
|
| A) Low gas pressure |
|
|
|
| B) Dirty or partially clogged ODS/pilot |
|
|
| 6. | Thermocouple damaged | 6. | Replace pilot assembly |
| 7. | Control valve damaged | 7. | Replace control valve |
| 8. | Safety interlock system has been trig- | 8. | Wait one minute for safety interlock sys- |
|
| gered (thermostat models only) |
| tem to reset. Repeat ignition operation |
|
|
|
|
|
Burner(s) does not light after ODS/pilot is lit | 1. | Burner orifice(s) is clogged | 1. | Clean burner orifice(s) (see Cleaning |
|
|
|
| and Maintenance, page 17) or replace |
|
|
|
| burner orifice(s) |
| 2. | Inlet gas pressure is too low | 2. | Contact local natural or propane/LP gas |
|
|
|
| company |
|
|
|
|
|
Delayed ignition of burner(s) | 1. | Manifold pressure is too low | 1. | Contact local natural or propane/LP gas |
|
|
|
| company |
| 2. | Burner orifice(s) is clogged | 2. | Clean burner orifice(s) (see Cleaning |
|
|
|
| and Maintenance, page 17) or replace |
|
|
|
| burner orifice(s) |
|
|
|
|
|
Burner backfiring during combustion | 1. | Burner orifice(s) is clogged or damaged | 1. | Clean burner orifice(s) (see Cleaning |
|
|
|
| and Maintenance, page 17) or replace |
|
|
|
| burner orifice(s) |
| 2. | Burner damaged | 2. | Replace burner |
| 3. | Gas regulator defective | 3. | Replace gas regulator |
|
|
|
|
|
Burner plaque(s) does not glow | 1. | Plaque damaged | 1. | Replace burner |
| 2. | Inlet gas pressure is too low | 2. | Contact local natural or propane/LP gas |
|
|
|
| company |
| 3. | Control knob set between locked posi- | 3. | Turn control knob until it locks at de- |
|
| tions |
| sired setting |
|
|
|
|
|
Slight smoke or odor during initial operation | 1. | Residues from manufacturing processes | 1. | Problem will stop after a few hours of |
|
|
|
| operation |
|
|
|
|
|
Heater produces a clicking/ticking noise just after burner is lit or shut off
1.Metal expanding while heating or con- tracting while cooling
1.This is common with most heaters. If noise is excessive, contact qualified ser- vice person
For
.
.com
107887
