Vermont Casting 1610CE Single-wall Chimney Connectors, Freestanding Installations

c)Mild steel fluepipes complying with BS 1449: Part 1: 1991, with a flue wall thickness of at least 3 mm;

d)Cast iron fluepipes complying with BS 41: 1973 (1998).

Flue Pipes with a spigot and socket joint should be fitted with the socket facing upwards, to contain con- densates and moisture within the flue. Joints should be made gas tight using proprietary jointing accessories, or, where appropriate, by packing joint with noncombus- tible rope and fire cement.

Single-wall connectors should be made of 24 gauge or heavier steel. Do not use galvanized connector; it cannot withstand the high temperatures that can be reached by smoke and exhaust gases, and may release toxic fumes under high heat. The connector may be 152 mm (6”) or 203 mm (8”) in diameter.

If possible, do not pass the chimney connector through a combustible wall or ceiling. If passage through a com- bustible wall is unavoidable, refer to the section on Wall Pass-Throughs. Do not pass the connector through an attic, a closet or similar concealed space. The whole connector should be exposed and accessible for in- spection and cleaning.

In horizontal runs of un shielded chimney connector, maintain a distance of 762 mm (30”) from the ceiling. Keep it as short and direct as possible, with no more than two 90° turns. Slope horizontal runs of connector upward 6mm per meter (1/4” per foot) going from the stove toward the chimney. The recommended maximum length of a horizontal run is 914 mm (36”), and the total length should be no longer than 2.4 m (8’). In cathedral ceiling installations, extend the prefabricated chimney downward to within 2.4 m (8’) of the stove. This will help maintain a good draft by keeping the smoke warm, so that it rises readily.

Wear gloves and protective eyewear when drilling, cut- ting or joining sections of chimney connector.

Single-wall Chimney Connectors

•Begin assembly at the flue collar of the stove. Insert the first crimped

end into the stove’s

flue collar, and	Toward
keep each crimped
	Stove
end pointing toward
the stove. (Fig. 4)
Using the holes
in the flue collar
as guides, drill 3		Flue Gas
mm (1/8”) holes
		Direction
in the bottom of
the first section of	ST242
chimney connector
and secure it to the	Fig. 4 Chimney connector.

Defiant 1610CE Non-Catalytic Woodburning Stove

flue collar with three #10 x 1/2” sheet metal screws. Lift off the griddle, and shield the stove’s surface between the griddle opening and the front of the flue collar to protect the finish when you drill the front hole.

•Fasten each joint between sections of chimney connector, including telescoping joints, with at least three (3) sheet metal screws. The pre-drilled holes in the top of each section of chimney connector serve as guides when you drill 3 mm (1/8”) holes in the bottom of the next section.

•Fasten the chimney connector to the chimney. Instructions for various installations follow. Figure 6 illustrates the general layout of chimney connector parts.

•Be sure the installed stove and chimney connector are correct distances from nearby combustible mate- rials.

NOTE: Special slip pipes and thimble sleeves that form telescoping joints between sections of chimney con- nector are available to simplify installations. They often eliminate the need to cut individual connector sections. Consult your local dealer about these special pieces.

Securing the Single-wall Connector to a

Prefabricated Chimney

Follow the installation instructions of the chimney manu- facturer exactly as you install the chimney. The manu- facturer of the chimney will supply the accessories to support the chimney, either from the roof of the house, at the ceiling of the room where the stove is installed, or from an exterior wall.

Special adapters are available from your local dealer to make the connection between the prefabricated chim- ney and the chimney connector. The top of such adapt- ers attaches directly to the chimney or to the chimney’s ceiling support package, while the bottom of the adapter is screwed to the chimney connector.

These adapters are designed so the top end will fit out- side the inner wall of the chimney, and the bottom end will fit inside the first section of chimney connector.

Securing the Single-wall Connector to a

Masonry Chimney

Both freestanding masonry chimneys and fireplace masonry chimneys may be used for your installation.

Freestanding Installations

If the chimney connector must pass through a com- bustible wall to reach the chimney, follow the recom- mendations in the Wall Pass-Through section that follows. The opening through the chimney wall to the flue (the “breech”) must be lined with either a ceramic or metal cylinder, called the “thimble”, which is cemented

30003846 7