|
|
| Manifold Gas Outlet | |
Brass |
|
| Brass Plug | |
Plug |
|
|
|
|
Thermostat |
|
|
| Pressure |
Bulb |
|
|
| |
|
|
| Regulator | |
|
|
|
| |
Gas Inlet |
|
|
|
|
Thermocouple |
|
|
|
|
Inlet |
|
|
|
|
Pilot Tube entry |
|
|
|
|
|
|
|
| Control |
Pilot Adjustment |
|
| Control | Knob |
Screw |
|
| Knob |
|
|
|
| HI |
|
|
| it | OFF |
|
| LO |
| PILOT |
|
|
|
|
| |
| Minimum | Fig. 3 | ||
| Rate Screw | |||
|
| |||
| ||||
On fireplaces equipped with Eurosit 630 gas valves there are brass plugs in two of the holes. These plugs are not to be removed. The gas inlet hole has a plastic cap in it. Remove the plastic cap and connect your gas supply line at this point. (Fig. 3).
INSTALLATION OF REMOTE
SWITCH FOR RN/RP GAS VALVE
Install on/off switch assembly on either the rear right or left side of the RFS22/RFS32/RFS42 Gas Fireplace.
1.Remove the screw at the back of the cabinet top either on the left or the right side of the fireplace.
2.Position switch assembly onto the back of the fireplace, then fasten two screws as shown in Fig. 5.
3.Attach wiring under the clips on the rear casing (Fig. 5) and install wiring through the rear opening of the fireplace before connecting to the valve as shown in Fig. 4.
VALVE |
|
|
|
|
TPTH |
|
| TH |
|
THERMOPILE |
|
|
|
|
TP |
|
| TP |
|
TH |
|
| TP TH | |
|
| P | PILOT |
|
| I |
| ||
| TOL |
| ADJ | |
|
|
| ||
ON/OFF SWITCH OR |
|
|
|
|
MILLIVOLT THERMOSTAT |
|
| Fig. 4 | |
|
|
| ||
OPTIONAL FAN KIT - FK24
STANDARD WITH RFS42
It will be easier to install the fan before connecting the gas line to the fireplace.
1.Open front access door panel by pulling forward on brass lip.
2.Guide the fan through the opening at the back of the pedestal, with the outlet pointed up and the fan mounting bracket facing the back of the fireplace. The fan mounts over two studs which hold the fan just below the firebox floor. Do not install this fan on the base. Hold the fan in place with the two nuts provided. (Fig. 7)
3.Locate the fan speed control/junction box on screw studs provided on base of the fireplace. Tighten with 3/8" nuts provided.
4.Install thermal sensor element on screw studs located to the right of the gas valve on the burner base.
5.Plug in grounded service cord to a convenient wall receptacle.
THIS FAN ASSEMBLY COMES COMPLETELY WIRED TO ELIMINATE THE NEED FOR ELECTRICIANS. THIS ELECTRICAL DEVICE, WHEN INSTALLED, MUST BE ELECTRICALLY CONNECTED AND GROUNDED IN ACCORDANCE WITH LOCAL CODES. IN THE ABSENCE OF LOCAL CODES, WITH THE CURRENT CSA C22.1 CANADIAN ELECTRICAL CODE.
FOR U.S.A. INSTALLATION: FOLLOW LOCAL CODES AND THE NATIONAL ELECTRICAL CODE ANSI/NFPA
Should this fan require servicing, the power supply must be disconnected. For rewiring of any replacement components see Fig. 6.
A = Speed Control | C | |
B = Temperature Sensor | B | |
C = Fan | ||
| ||
| A | |
BLACK |
| |
WHITE |
| |
GROUND | Fig. 6 |
On/off switch |
assembly |
Clips
Screw (through existing hole)
Screw
Wiring for
Thermal sensor location
Valve
Stud
Fan is installed at the back of the pedestal
Fan speed control/ Junction box
Fig. 5
- 6 -
TOP VIEW
Fig. 7
