2 Wall Construction

This Built-in Microwave Hood should be mounted against and supported by a flat vertical wall. The wall must be flat for proper installation. If the wall is not flat, use spacers to fill in the gaps. Wall construction should be a minimum of 2” x 4” wood studding and 3/8” or more thick dry wall or plaster/lath. The mounting surfaces must be capable of supporting a weight of 110 pounds—the oven and contents—AND the weight of all items which would normally be stored in the top cabinet above the unit. The unit should be attached to a minimum of one 2” x 4” wall stud.

To find the location of the studs, one of the following methods may be used:

•Use a stud finder, a magnetic device which locates the nails in the stud.

•Use a hammer to tap lightly across the mounting surface to find a solid sound. This will indicate stud location.

The center of the stud can be located by probing the wall with a small nail to find the edges of the stud and then placing a mark halfway between the edges. The center of any adjacent studs will normally be 16” or 24” to either side of this mark.

3Electrical Grounding

Instructions

This appliance must be grounded. This oven is equipped with a cord having a grounding wire with a grounding plug. It must be plugged into a wall receptacle that is properly installed and grounded in accordance with the National Electrical Code and local codes and ordinances. In the event of an electrical short circuit, grounding reduces risk of electric shock by providing an escape wire for the electric current.

WARNING: Improper use of the grounding plug can result in a risk of electric shock.

Electrical Requirements

The oven is equipped with a 3-prong grounding plug. DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE GROUNDING PIN FROM THE PLUG.

DO NOT USE AN EXTENSION CORD.

If the power supply cord is too short, have a qualified electrician or serviceman install an outlet near the appliance.

The Power Supply Cord and plug must be connected to a separate 120 Volt AC, 60 Hz, 15 Amp, or more branch circuit, single grounded receptacle. The receptacle should be located inside the cabinet directly above the Built-in Microwave Hood mounting location as shown in figure 2.

NOTE:

•If you have any questions about the grounding or electrical instructions, consult a qualified electrician or serviceperson.

•Neither Viking nor the dealer can accept any liability for damage to the oven or personal injury resulting from failure to observe the correct electrical connection procedures.

figure

Ground

Receptacle

 

 

*Opening for

 

Power Cord

IMPORTANT: * Power cord opening for metal cabinets: Deburr opening to remove rough edges.

Radio or TV Interference

Should there be any interference caused by the Built-in Microwave Hood to your radio or TV, check that the oven is on a different electrical circuit, relocate the radio or TV as far away from the oven as feasible or check position and signal of receiving antenna.

E2

Page 1 Page 3
Page 2
Image 2
Viking D3 manual Wall Construction, Ground, Receptacle, Opening for, Power Cord
Page 1 Page 3

D3 specifications

The Viking D3 is a cutting-edge vehicle known for its robust design and advanced features, making it a standout choice in the off-road segment. This model is particularly favored among adventurers and outdoor enthusiasts due to its ability to tackle various terrains with ease.

One of the key characteristics of the Viking D3 is its powerful engine. Equipped with a high-performance engine, it delivers impressive torque and horsepower, which translates into exceptional acceleration and pulling power. This capability allows drivers to navigate challenging landscapes, from rugged mountain trails to muddy fields, without compromising performance.

The Viking D3 is built on a durable chassis designed for stability and strength. Its reinforced frame provides the necessary support to endure heavy loads and tackle harsh environments. Additionally, the vehicle features a sophisticated suspension system that enhances ride comfort, absorbs shocks from uneven surfaces, and ensures optimal traction.

Incorporating cutting-edge technologies is another highlight of the Viking D3. It comes equipped with advanced safety features, including electronic stability control and anti-lock braking systems, which contribute to safer driving experiences. The vehicle also often includes modern navigation systems and connectivity options, allowing users to stay connected even in remote areas.

User comfort and convenience are enhanced by the Viking D3's spacious interior. The ergonomic seating design provides ample legroom and headspace for both the driver and passengers, while storage compartments are strategically placed for easy access to gear and essentials.

The Viking D3 also emphasizes versatility with its multi-functional capabilities. Users can customize the vehicle with various accessories, from additional seating to specialized equipment for specific activities like hunting or hiking. This adaptability makes the Viking D3 a practical choice for those seeking both leisure and work-related functionalities.

Furthermore, the Viking D3 is designed with fuel efficiency in mind. The integration of eco-friendly technologies helps optimize fuel consumption, making it a more sustainable option for off-road adventures.

In summary, the Viking D3 represents a perfect balance of power, technology, and comfort. Its robust construction, advanced features, and versatility make it an excellent choice for those looking to explore the great outdoors with confidence and style. Whether navigating through dense forests or cruising along scenic routes, the Viking D3 is engineered to deliver an unparalleled driving experience.
Top Page Image Contents