Viking MCX-106 Specifications, Maximum Voltage Gain, Peak Indicators, Power Output at Clipping

Specifications

MIXER SECTION

Frequency Response

+0, -3dB 30Hz~20kHz (HIGH Z input TRIM at "0" positio

Total Harmonic Distortion

0.05% +4dBm at 1kHz.

Hum and Noise (Open)

Equivalent Input Noise	-130dBm (20Hz~20kHz
Equivalent Input Noise	-133dBm (IHF A)
All level Controls Minimum	-102dBm (IHF A)
PGM Master at MAX and all
input level controls minimum -93dBm (IHF A)
PGM Master at MAX and one
input level control at MAX	-72dBm (IHF A)

INPUT SPECIFICATIONS

		ACTUAL	FOR USE
CONNECTION	INPUT	LOAD	WITH
		IMPEDANCE	NOMINAL
CH1	LOW Z	OPEN	MICRO-
			PHONES
CH6	HIGH Z		LOWER IMP
			LINES
AUX (L & R)			LOWER IMP,
			LINES
EFF/RET			LOWER IMP,
			LINES
GEQ			LOWER IMP,
			LINES
PWR			LOWER IMP
			LINES
BUSS LINK			LOWER IMP
(PGM, FB, EFF)
			LINES
OUTPUT SPECIFICATIONS
CONNECTION	ACTUAL LOAD		FOR USE WITH
	IMPEDANCE		NOMINAL

PGM	IMP. LINES
EFF	IMP. LINES
GEQ	IMP. LINES
FB	IMP. LINES
REC L & R	IMP. LINES
TAPE L & R	IMP. LINES

	Maximum Voltage Gain
	INPUT to PGM out			59dB
	INPUT to EFF out			45dB
	INPUT to FB out			59dB
	INPUT to REC out			45dB
	INPUT to GEQ out			59dB
	AUX to PGM out		14dB
	EFF/RET to PGM out			24dB
	Equalization
	63Hz ±12dB Peaking			2kHz ±12dB Peaking
	125Hz ±12dB Peaking			4kHz ±12dB Peaking
	250kHz ±12dB Peaking			8kHz ±12dB Peaking
	500Hz ±12dB Peaking			16kHz ±12dB Peaking
	1kHz ±12dB Peaking
	Peak Indicators
	Red LED on each input channel LED's turn on at 3dB below
	clipping.
TRIM	SENSITIVITY	MAX BEFORE
POSI-	(PGM OUTPUT	CLIP INPUT			CONNECTOR
TION	LEVEL +4dB)	LEVEL
10	-55dBm (1.38mV)	-34dBm (15mV)			XLR TYPE NC3F
0	-16dBm (123mV)	+1.7dB (0.94V)
10	-35dBm(13.8mV)	-14dBm (150mV)			PHONE JACK
0	+4dBm (1.23mV)	+20dB (7.75V)
	-l0dBm (245mV)	+8dBm (1.9V)			PHONE JACK
					RCA PIN JACK
	-20dBm (77.5mV)	-2dBm (0.61V)			PHONE JACK
	+4dBm (1.23V)				PHONE JACK
	+4dBm (1.23V)				PHONE JACK
	+4dBm (1.23V)	+20	dBm	(7.75V)	PHONE JACK
	OUTPUT LEVEL				CONNECTOR
NOMINAL		MAX. BEFORE
		CLIP
+4dB (1.23V)		+20dB (7.75V)			PHONE JACK
+10dB (245V)		+8dB (1.9V)			PHONE JACK
+4dB (1.23V)		+20dB (7.75V)			PHONE JACK
+4dB (1.23V)		+20dB (7.75V)			PHONE JACK
-l0dB (7.75V)		+8dB (1.9V)			RCA PIN JACK
0dB (0.775V)		+20dB (7.75V)			RCA PIN JACK

POWER AMPLIFIER SECTION

Frequency Response

+0, -1dB 5Hz to 40kHz (200W RMS

Rated Power & Load

300W RMS	200W	RMS	120W RMS
Power Output at Clipping
1% THD, 1kHz			140W RMS
348W RMS	238W	RMS

Total Harmonic Distortion

Less than 0.1% (200mW~200W RMS, 20Hz~20kHz) Typically below 0.05%

Compressor Dynamic Range

Greater than 26dB

Hum and Noise

At least 110dB S/N ratio, 20Hz~20kHz At least 113dB S/N ratio IHF-A weighted

Damping Factor

Greater than 200 (1kHz

Input Sensitivity

+4dBm (1.23V)

Input Impedance

Output Connector

Phone Jack X2

Power Requirement

600 W 120V AC 50/60Hz

Dimensions (WXHXD)

605X371X356mm (23.8X14.6 X14.0) inch

Weight

27.2 kg (60 Ibs)

*0dBm is referenced to 0.775V RMS.

Specifications are subject to change without notice.

— 12 —