Manuals / Viking / Computer Equipment / Computer Drive

Viking PSFEM1xxxGQxxx manual Command Sets, Hot Plug Support, 1 Supported ATA Commands

Models: PSFEM1xxxGQxxx

1 33

Download 33 pages 18.54 Kb

Page 19

Table 4-2: Serial ATA Power Pin Definitions

Table 4-2: Serial ATA Power Pin Definitions

Pin

P1

P2

P3

P4

P5

P6

P7

P8

P9

P10

P11

P12

P13

P14

P15

Notes:

Function	Definition	Mating Order
3.3V_1	No connection	2nd
3.3V_2	No connection	2nd
3.3V_3	No connection	1st
GND_1	Ground	1st
GND_2	Ground	1st
GND_3	Ground	1st
5V_1	5VDC Power (pre-charge)	1st
5V_2	5VDC Power	2nd
5V_3	5VDC Power	2nd
GND_4	Ground	1st
Activity	Device Activity Signal (See note1)	2nd
GND_5	Ground	1st
12V_1	No connection	1st
12V_2	No connection	2nd
12V_3	No connection	2nd

1)Remote LED is not implemented, pin 11 may be connected to GND to allow the ACTIVITY LED to remain on to indicate a Power On condition when using a standard ATX type power supply.

4.3Hot Plug Support

Hot Plug insertion and removal are supported in the presence of a proper connector and appropriate operating system (OS) support as described in the SATA 2.6 specification. This product supports Asynchronous Signal Recovery and will issue an unsolicited COMINIT when first mated with a powered connector to guarantee reliable detection by a host system without hardware device detection.

5 Command Sets

5.1 ATA Commands

Table 5-1: Supported ATA Commands

Description		Op		Description		Op
Description		Code		Description		Code
		Code				Code
Check power mode		E5h		Security Disable Password		F6h

Data Set management	06h			Security Erase Prepare	F3h
DCO		B1h		Security Erase Unit		F4h

Download Microcode PIO	92h			Security Freeze Lock	F5h

Download Microcode DMA		93h		Security Set Password		F1h
Execute drive diagnostic		90h		Security Unlock		F2h
Flush cache		E7h		Seek		70h

Manual

PSFEM1xxxGQxxx

Revision B www.vikingtechnology.com

9/11/2014

Viking Technology

Page 19 of 33

Image 19

Viking PSFEM1xxxGQxxx manual Command Sets, Hot Plug Support, ATA Commands, 2 Serial ATA Power Pin Definitions

Contents

Manual PSFEM1xxxGQxxx SATA 3Gb/s Industrial Slim SATA Manual9/11/2014 Viking Technology Page 1 of Description Revision HistoryDate RevisionLegal Information Legal InformationTemperature Ordering Information Slim SATA SSD Solid-State DriveInterface Slim SATA Top View Product PicturesIndustrial SSD - Viking’s Industrial SSD contains sophisticated provisions to protect firmware and data from corruption due to unexpected power loss. However, a Industrial SSD by industry definition does not contain on-board capacitance. Should power fail unexpectedly, “in-flight” write data may be lost. Industrial SSD’s are best used in designs that manage power fail events at the system level 5 COMMAND SETS Table of Contents2 PRODUCT SPECIFICATIONS PIN AND SIGNAL DESCRIPTIONSSATA Commands REFERENCESGLOSSARY ATA CommandsTable of Figures Table of Tables1 Introduction 1.1 FeaturesFigure 1-1 High-Level Block Diagram for VRFEM1xxxGQxxx 1.2 Block Diagram1.3 SATA Interface 2.2 Timing 2 Product SpecificationsTable 2-3 Timing Specifications 2.1 Performance2.3.2 Supply Voltage 2.3 Electrical Characteristics2.2.1 STANDBY IMMEDIATE Command 2.3.1 Absolute Maximum RatingsTable 2-8 Temperature and Altitude Related Specifications 2.3.3 Power Consumption2.4.1 Temperature and Altitude Table 2-7 Typical Power Consumption2.5 Reliability Table 2-10 Reliability Specifications2.6 Data Security 3 Mechanical Information Figure 3-1 DimensionsFigure 4-1 Layout of Signal and Power Segment Pins 4 Pin and Signal Descriptions3.1 Slim SATA SSD Weight Signal and Power Description TablesTable 5-1 Supported ATA Commands 5 Command Sets5.1 ATA Commands Table 4-2 Serial ATA Power Pin DefinitionsRead Sectors Ext Set Max Address Ext Write DMA Ext Write Multiple Ext 5.1.1 48-Bit Address Command SetSSD supports the 48-Bit Address command set consisting of Flush Cache Ext Read DMA Ext Read native Max Address Ext5.1.5 Host Protected Area Command Set 5.1.2 ATA General Feature Command Set5.1.3 Device Configuration Overlay Command Set 5.1.4 General Purpose Log Command Set5.1.7 Security Mode Feature Set 5.1.6 Power Management Command SetTable 5-2 List of Device Identification 5.1.8 Identify Device DataDescription Default ValueWord V VariableDescription Default ValueWord V VariableTable 5-3 Capacity specific Device Identification 5.1.1 S.M.A.R.T. Support5.1.2 S.M.A.R.T. Command Set 5.1.2.1 Extended SMART Attributes Table 5-4 S.M.A.R.T. Command SetTable 5-5 Extended SMART Attribute Table SMART Attribute Table 5-6 Extended SMART Attribute Actual DataDescription Fla7 = 100*Max Erase Count- F1a4/Flash PE Cycle MLC 3000, SLC FormulaFla4 = Total Erase Count / disk Total Blocks average Erase Count Fla6 = 100 * D- Total Bad Block Count / D-E Max = 100, Min =5.1.2.2 Off-line Mode 5.2 SATA Commands5.2.1 Native Command Queuing NCQ Table 5-7 Supported S.M.A.R.T. EXECUTE OFF-LINE IMMEDIATE SubcommandsSerial ATA Specification, Revision 6 References7 Glossary