Manuals / Viking / Computer Equipment / Computer Drive

Viking PSFEM1xxxGQxxx manual Environmental Conditions, Power Consumption, Temperature and Altitude

Models: PSFEM1xxxGQxxx

1 33

Download 33 pages 18.54 Kb

Page 15

2.3.3 Power Consumption

2.3.3 Power Consumption

All onboard power requirements of the SSD are derived from the SATA 5.0V input rail.

Table 2-7: Typical Power Consumption

Mode	Typical	Unit
Active	tbd	W
Idle	tbd	W

2.4Environmental Conditions

2.4.1Temperature and Altitude

Table 2-8: Temperature and Altitude Related Specifications

Conditions	Operating	Shipping	Storage
Commercial	0 to 70°C	-40 to 85°C	-40 to 85°C
Temperature	(32 to 158° F)	(-40 to 185° F)	(-40 to 185° F)
- Ambient
Industrial	-40 to 85°C	-40 to 85°C	-40 to 85°C
Temperature	(-40 to 185° F)	(-40 to 185° F)	(-40 to 185° F)
- Ambient
Humidity (non-	95% under 55C	95% under 55C	95% under 55C
condensing)

Notes:

1.SLC flash based products may be available in the following temperature ranges:

a)Commercial temperature range of 0 to 70°C (32 to 158° F)

b)Industrial temperature range -40 to 85°C (-40 to 185° F)

2.4.2 Shock and Vibration

SSD products are tested in accordance with environmental specification for shock and vibration

Table 2-9: Shock and Vibration Specifications

		Description
	Shock	50g, 11ms, 3 shocks applied in each direction on 3 mutually perpendicular
	Shock	axes X, Y, Z
		axes X, Y, Z
	Vibration	16.4g rms 10-2,000 Hz, 3 axes

2.4.3 Electromagnetic Immunity

SSD is an embedded product for host systems and is designed not to impair with system functionality or hinder system EMI/FCC compliance.

Manual

PSFEM1xxxGQxxx

Revision B www.vikingtechnology.com

9/11/2014

Viking Technology

Page 15 of 33

Image 15

Viking PSFEM1xxxGQxxx manual Environmental Conditions, Power Consumption, Temperature and Altitude, Shock and Vibration

Contents

SATA 3Gb/s Industrial Slim SATA Manual Manual PSFEM1xxxGQxxx9/11/2014 Viking Technology Page 1 of Description Revision HistoryDate RevisionLegal Information Legal InformationOrdering Information Slim SATA SSD Solid-State Drive TemperatureInterface Slim SATA Top View Product PicturesIndustrial SSD - Viking’s Industrial SSD contains sophisticated provisions to protect firmware and data from corruption due to unexpected power loss. However, a Industrial SSD by industry definition does not contain on-board capacitance. Should power fail unexpectedly, “in-flight” write data may be lost. Industrial SSD’s are best used in designs that manage power fail events at the system level 5 COMMAND SETS Table of Contents2 PRODUCT SPECIFICATIONS PIN AND SIGNAL DESCRIPTIONSSATA Commands REFERENCESGLOSSARY ATA CommandsTable of Figures Table of Tables1 Introduction 1.1 FeaturesFigure 1-1 High-Level Block Diagram for VRFEM1xxxGQxxx 1.2 Block Diagram1.3 SATA Interface 2.2 Timing 2 Product SpecificationsTable 2-3 Timing Specifications 2.1 Performance2.3.2 Supply Voltage 2.3 Electrical Characteristics2.2.1 STANDBY IMMEDIATE Command 2.3.1 Absolute Maximum Ratings2.4 Environmental Conditions 2.3.3 Power ConsumptionTable 2-7 Typical Power Consumption Table 2-9 Shock and Vibration SpecificationsTable 2-10 Reliability Specifications 2.5 Reliability2.6 Data Security 3 Mechanical Information Figure 3-1 DimensionsFigure 4-1 Layout of Signal and Power Segment Pins 4 Pin and Signal Descriptions3.1 Slim SATA SSD Weight Signal and Power Description TablesTable 5-1 Supported ATA Commands 5 Command Sets5.1 ATA Commands Table 4-2 Serial ATA Power Pin DefinitionsRead Sectors Ext Set Max Address Ext Write DMA Ext Write Multiple Ext 5.1.1 48-Bit Address Command SetSSD supports the 48-Bit Address command set consisting of Flush Cache Ext Read DMA Ext Read native Max Address Ext5.1.5 Host Protected Area Command Set 5.1.2 ATA General Feature Command Set5.1.3 Device Configuration Overlay Command Set 5.1.4 General Purpose Log Command Set5.1.7 Security Mode Feature Set 5.1.6 Power Management Command SetTable 5-2 List of Device Identification 5.1.8 Identify Device DataDescription Default ValueWord V VariableDescription Default ValueWord V VariableTable 5-3 Capacity specific Device Identification 5.1.1 S.M.A.R.T. Support5.1.2 S.M.A.R.T. Command Set Table 5-4 S.M.A.R.T. Command Set 5.1.2.1 Extended SMART AttributesTable 5-5 Extended SMART Attribute Table Table 5-6 Extended SMART Attribute Actual Data SMART AttributeDescription Fla7 = 100*Max Erase Count- F1a4/Flash PE Cycle MLC 3000, SLC FormulaFla4 = Total Erase Count / disk Total Blocks average Erase Count Fla6 = 100 * D- Total Bad Block Count / D-E Max = 100, Min =5.1.2.2 Off-line Mode 5.2 SATA Commands5.2.1 Native Command Queuing NCQ Table 5-7 Supported S.M.A.R.T. EXECUTE OFF-LINE IMMEDIATE SubcommandsSerial ATA Specification, Revision 6 References7 Glossary