Level Control for Effect and Reverb Return to Aux 1 (REV/EFF TO AUX, LEVEL AUX 1)

This control governs the amount of reverb signal (built-in or outboard) returned through the reverb return jack (REV RET), and effect signal returned through the effect return jack (EFF RET) to AUX 1 mixing buss. The signals of REV RET and EFF RET are controlled simultaneously.

Cross-fade Control to Aux 1 (REV/EFF TO AUX, X-FADE)

When this control is in the center position, the REV RET and EFF RET signals are equally assigned to the AUX 1 mixing buss. Rotating the control counter- clockwise decreases the EFF RET signal level, keeping the original level of the REV RET signal. Rotating the control clockwise decreases the REV RET signal level, keeping the original level of the EFF RET signal.

Level Control for Effect and Reverb Return to Aux 2 (REV/EFF TO AUX, LEVEL AUX 2)

This control governs the amount of reverb signal (built-in or outboard) returned through the reverb return jack (REV RET), and effect signal returned through the effect return jack (EFF RET) to AUX 2 mixing buss. The signal of REV RET and EFF RET are controlled simultaneously.

Cross-Fade Control to Aux 2 (REV/EFF TO AUX, X-FADE)

When the control is in the center position, the REV RET and EFF RET signals are equally assigned to the AUX 2 mixing buss. Rotating the control counter- clockwise decreases the signal level of the EFF RET,

keeping the original level of the REV RET signal.

Rotating the control clockwise decreases the signal level of the REV RET, keeping the original level of

the EFF RET signal.

Cue Out Level Control and Cue ON LED Indicator (CUE OUT, CUE)

The cue out level control adjusts both the stereo L and R signals and the Cue in (L, R) signal fed to the Cue output on the rear panel (CUE OUT) and permits stereo monitoring when the cue switch is "off". When the cue switch is "on", the control adjusts the

corresponding cue signal. When two or more of the

cue switches are "on", the control adjusts the corresponding combined cue signals. The cue on LED lights when one of the cue switches is "on".

Headphone Level Control and Jack (PHONES)

The phones level control adjusts both the stereo L and R signals and the Cue IN (L, R) signal fed to the phones output and permits stereo monitoring when the cue switch is "off". When the cue switch is "on", the control adjusts the corresponding cue signal. When two or more of the cue switches are "on", the control adjusts the corresponding combined cue signals. The headphone jack will accept any stereo

headphone with 8 ohms impedance, or higher.

Signal/Peak LED Indicator (SIG/PEAK)

The LED indicator lights green when the stereo out L or R signals reach more than -30dB, and turns to red when the stereo out L or R signals reach -3dB below clipping, giving a visual reference of adjustment of the stereo L or R faders. (See NOTE 1)

Stereo Channel ON Indicator and Channel ON/OFF Switch (CHANNEL ON)

The LED indicator lights orange when the channel

switch is "on".

Writing Block

Stereo Left and Right Fader (STEREO L, R)

The fader provides continuously variable adjust- ment of the stereo L or R output, and the signal level to the Sum out channel when the sum select switch is set in the "POST" position.

Cue Switch (CUE)

The cue switch permits monitoring the pre stereo L, R fader signals through the headphones and cue out.

Power LED indicator and Switch (POWER)

The power switch alternately turns AC power to the D-5.5 "on" and "off". The LED indicator lights when the switch is "on".

Dual LED Bargraph Meter and Meter Select Switch (METER SELECT, SUM/CUE, L/R)

The meter indicates the sum output (left side) and cue output (right side) when the meter select switch is set in the "push" position, and indicates the stereo L output (left side) and stereo R output (right side)

when the meter select switch is set in the "release"

position.

— 9 —

Page 10
Image 10
Vizio D-5.5E Cross-fade Control to Aux 1 REV/EFF to AUX, X-FADE, Cross-Fade Control to Aux 2 REV/EFF to AUX, X-FADE