C24GA SERIES GAS CONVECTION STEAMERS

instructions provided with the filter system. At the time of installation you must register your steamer at www.vulcanhart.com/ filterreg or use the reply card supplied with your unit. You will need to register your steamer at each filter change to insure your standard and extended warranty is maintained.

Drain Connection

The 1½" NPT threaded fitting on the condenser box must be extended a minimum of 12" (305

mm)- maximum of 72" (1829 mm) away from steamer base, to an open air gap type drain. Do not reduce the 1 ½" NPT drain piping throughout its length. Provide a suitable floor sink with a minimum depth of 12" (305 mm). The floor sink is NOT to be directly under the steamer and should be at a distance so that steam vapors will not enter the steamer from underneath. The drain should slope down away from the steamer ¼" for every foot of drain pipe length. The drain pipe should be either iron or copper. DO NOT use PVC pipe; PVC pipe may lose its rigidity or glue may fail.

In order to avoid any back pressure in the steamer, do not connect solidly to any drain connection.

Temperatures in the generator can briefly reach as high as 212°F (l00°C). Local codes may require that the temperature of drain water be no greater than 140°F (60°C). At the end of the day, when purging the generators, some provision for lowering the water temperature must be provided by the user or installer to meet this code requirement.

GAS SUPPLY CONNECTION

All gas supply connections and any pipe joint compound used must be resistant to the action of propane gas. A ¾" NPT minimum inside diameter gas supply line is required. If quick disconnect devices are used, make sure it is sized properly for data plate BTU/hr. rating. Refer to quick connect supplier’s data sheet.

Codes require that a manual gas shutoff valve be installed in the gas line ahead of the steamer.

The gas line must be capable of delivering gas to the generator without excessive pressure drop at the minimum rate specified on the rating plate.

Check blower air pressure at gas manifold pressure tap by shutting off the gas valve. Air pressure at cold start-up should be 0.35" W.C. (0.09 kPa) (cold condition). After 15 minutes, air pressure should be between 0.40" W.C. (0.1 kPa) and 0.50" W.C. (0.13 kPa) (hot condition). Turn the air pressure adjust screw clockwise to increase pressure and counterclockwise to reduce pressure.

Gas Input:

¾" NPT

Natural:

5" _ 10.5" W.C.

Propane:

11" _ 13" W.C.

Inadequate gas supply could result in burner noise and poor burner performance.

Refer to the instruction manual supplied with the machine for INSTALLATION CODES AND STANDARDS and GAS CONNECTION information.

— 6 —

Page 5 Page 7
Page 6
Image 6
Vulcan-Hart C24GA10 ML-136057, C24GA6 ML-136021, C24GA6 ML-136056, C24GA10 ML-136022 GAS Supply Connection, Drain Connection
Page 5 Page 7

C24GA10 ML-136022, C24GA10 ML-136057, C24GA6 ML-136056, C24GA6 ML-136021 specifications

The Vulcan-Hart C24GA series, including models C24GA6 ML-136056, C24GA6 ML-136021, C24GA10 ML-136022, and C24GA10 ML-136057, represents a pinnacle of efficiency and performance in commercial cooking equipment. Designed specifically to meet the demanding needs of busy kitchens, these versatile gas ranges are built to provide exceptional service and durability.

One of the standout features of the C24GA series is its powerful burners. With multiple BTU output options, these ranges allow chefs to achieve precise temperatures for various cooking techniques, whether boiling, sautéing, or simmering. The high-efficiency burners are designed to distribute heat evenly across the cookware, ensuring consistent cooking results and reducing the risk of hot spots.

The C24GA models are constructed with robust stainless steel bodies, ensuring not only durability but also ease of cleaning. The polished finish helps maintain a professional look in any kitchen environment. The heavy-duty grates are designed for stability and support, accommodating different sizes of pots and pans. The grates are also dishwasher safe, making maintenance straightforward.

One of the technological advancements featured in the C24GA series is the electronic ignition system. This feature enhances safety by eliminating the need for pilot lights, reducing gas emissions and minimizing the risk of gas buildup. The system provides quick and reliable ignition with a simple turn of the knob, an asset in high-pressure kitchen scenarios.

In terms of configuration, the range is designed with adaptability in mind. The modular design allows for various combinations and configurations tailored to specific kitchen layouts and workflow requirements. Whether it’s integrating with other pieces of equipment or fitting into tight spaces, the C24GA range provides flexibility for chefs and kitchen planners alike.

Moreover, the C24GA series includes easy-to-access controls positioned at the front, allowing chefs to adjust flames effortlessly while monitoring cooking progress. The continuous belt of knobs provides a user-friendly experience, ensuring that meal preparation flows smoothly.

In conclusion, the Vulcan-Hart C24GA6 and C24GA10 models exemplify the attributes essential for any high-volume kitchen. With their durable construction, efficient burners, user-friendly features, and modern technologies, they are an ideal choice for restaurants, caterers, and institutional kitchens seeking reliable performance and versatility in their cooking operations. Investing in a Vulcan-Hart C24GA range is a commitment to quality, efficiency, and the culinary excellence that modern dining demands.
Top Page Image Contents