USA FCC Part 15
FCC Notice to Users/Product Statements
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Users are not permitted to make changes or modify the device in any way. Changes or modifications not approved by VXI Corporation will void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer- ence in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accor- dance with the instructions, may cause harmful interference to radio communications. However, there is no guar- antee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encour- aged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The user must place the base at least 8” (20cm) or more from any personnel and must not be
USA FCC Part 68
FCC Notice to Users/Product Statements
1.This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bot- tom of the base of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.
2.If this device is malfunctioning, it may also be causing harm to the telephone network. The device should then be disconnected until the source of the problem can be determined and until repair has been made. If this is done, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the telephone company will notify the customer as soon as pos- sible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
3.The Universal Service Order Codes (USOC) for both the Line port and Phone port beneath the base is
4.The telephone company may make changes in its facilities, equipment, operations and/or procedures that may affect the operation of this equipment. If this happens, the telephone company will provide advanced notice in
order for you to take the necessary steps to maintain uninterrupted service.
5.If the telephone company requests information on what equipment is connected to their lines, inform them of:
(a)The telephone number that this unit is connected to.
(b)The FCC Registration number located on the label.
6.A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.
7.The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be con- nected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.
8.If trouble is experienced with this BlueParrott B200 system, for repair or warranty information, please contact VXI Corporation at
9.Repair of this product must be handled by VXI Corporation. For more information about repairs, please read the warranty section of this user guide or call VXI Corporation at
10.Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.
11.If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this BlueParrott B200 system does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
Canada
IC Notice to Users/Product Statements
Operation is subject to the following two conditions:
(1)This device may not cause interference and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
The term “IC:” before the certification/registration number only signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that industry Canada approved the equipment.
Canada Terminal equipment
IC Notice to Users/Product Statements
NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number.
22 | 23 |
|
|
