5
Connect Power Source:
If powered by Power Supply: Plug power supply into source.
If powered by Operator: Connect wires to the proper operator accessory supply source (10 V AC/DC to 28 V AC/DC source).
1.
2.Using wall control, activate door or gate operator to confi rm power connection.
6(continued)
To Erase All Learned Transmitters:
1.Press and hold down the PROGRAM button.
2.After 10 seconds, the red STATUS LED will blink 5 times indicating all transmitters are erased from the receiver’s memory.
3.Release the PROGRAM button.
4.
7
Symptom | Possible Solution |
1. Receiver’s red STATUS | Check power source to receiver. Insure |
LED does not turn on | proper 10 VAC/DC minimum to 28 VAC/ |
when programming button | DC maximum power source. |
pressed. |
|
2. No transmitter range | Check antenna connections and, if in- |
(less than 10 ft). | stalled, check antenna extension kit coax |
| wire for damage or kinks. Correct antenna |
| connection or replace coax as needed. |
3. Poor transmitter range | Insure antenna is not near any metal. Re- |
(less than 50 ft). | position antenna from vertical to horizontal |
| position or vice versa. Possible |
| radio interference. |
4. With transmitter | Check relay (RLY) wire connections. In- |
activation, the receiver’s | sure relay wire is not broken or damaged. |
STATUS LED lights and | Insure relay wire is connected to proper |
a ”click” is heard within | terminals on operator. Using insulated |
receiver, but receiver does | pliers or insulated screwdriver, short RLY |
LIMITED WARRANTY
THE MANUFACTURER
THE ABOVE CONDITIONS APPLY PROVIDED THAT THE ABOVE REFERENCED RADIO RECEIVER MODEL
THIS LIMITED WARRANTY EXTENDS ONLY TO THE ORIGINAL PURCHASER, PROVIDED THE ABOVE REFERENCED RADIO RECEIVER IS PROPERLY INSTALLED, USED, MAINTAINED, AND SERVICED. THIS LIMITED WARRANTY IS NOT TRANSFERABLE.
NO EMPLOYEE, DISTRIBUTOR, OR REPRESENTATIVE IS AUTHORIZED TO CHANGE THE FOREGOING WARRANTIES IN ANY WAY OR GRANT ANY OTHER WARRANTY ON BEHALF OF MANUFACTURER.
THE MANUFACTURER SHALL NOT BE RESPONSIBLE FOR ANY DAMAGE RESULTING TO OR CAUSED BY ITS PRODUCTS BY REASON OF INSTALLATION, IMPROPER STORAGE, UNAUTHORIZED SERVICE, ALTERATION OF PRODUCTS, NEGLECT OR ABUSE, ANY ACTS OF NATURE BEYOND MANUFACTURER’S CONTROL (SUCH AS, BUT NOT LIMITED TO, LIGHT- NING, POWER SURGES, WATER DAMAGE, ETC.), OR ATTEMPT TO USE THE PRODUCTS FOR OTHER THAN THE CUSTOMARY USAGE OR FOR THEIR INTENDED PURPOSES. THE ABOVE
6
Programming:
WARNING: Keep away from all
WARNING: During programming, door or gate operator will acti- vate. Keep people and objects away from door or gate.
1. Test receiver by operating a |
compatible RF transmitter. The |
Receiver’s STATUS LED will |
fl ash indicating reception. |
PROGRAM BUTTON
Safe Operation Precautions
WARNING: To reduce the risk of severe or fatal injury.
1.Always keep a moving door or gate in sight and keep people and objects away until it is completely opened or closed.
2.No one should cross the path of a moving door or gate.
3.Never let children operate or play with the controls. Keep all controls away from children.
4.Never go under a stopped, partially open door. Never walk through a vehicular entry gate; always use the pedestrian entry.
5.Keep fi ngers and other body parts away from the all moving parts of the door, gate and operator system while the system is being operated.
6.Periodically test the safety systems of the door or gate. Disconnect and do not use this receiver if any of your door or gate’s safety systems fail their tests. Then have door or gate operator serviced immediately.
7.SAVE THESE INSTRUCTIONS.
not activate operator. | terminals on receiver and this should |
| activate operator. Test operator for proper |
| operation. |
5. Can not learn transmit- | Insure transmitter is a correct transmitter |
ter. | for this receiver. Check this receiver’s RF |
| frequency and the companion transmitter’s |
| frequency to insure they are identical. Test |
| receiver with another transmitter. |
WARRANTY DOES NOT COVER NORMAL WEAR OR ANY DAMAGE BEYOND MANUFACTUR- ER’S CONTROL OR REPLACEMENT LABOR.
CLAIMS FOR DEFECTS IN MATERIAL AND WORKMANSHIP COVERED BY THIS WARRANTY SHALL BE MADE IN WRITING, WITHIN THE WARRANTY PERIOD, TO THE DEALER TO WHOM THE PRODUCT WAS PURCHASED. MANUFACTURER MAY EITHER SEND A SERVICE REPRE- SENTATIVE OR HAVE THE PRODUCT RETURNED TO THE MANUFACTURER AT BUYER’S EX- PENSE FOR INSPECTION. IF JUDGED BY MANUFACTURER TO BE DEFECTIVE IN MATERIAL OR WORKMANSHIP, THE PRODUCT WILL BE REPLACED OR REPAIRED AT THE OPTION OF THE MANUFACTURER, FREE FROM ALL CHARGES EXCEPT AUTHORIZED TRANSPORTATION AND REPLACMENT LABOR.
THE REMEDIES OF BUYER SET FORTH HEREIN ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER REMEDIES, THE LIABILITY OF MANUFACTURER, WHETHER IN CONTACT, TORT, UNDER ANY WARRANTY OR OTHERWISE, SHALL NOT EXTEND BEYOND ITS OBLIGATION TO REPAIR OR REPLACE, AT ITS OPTION, ANY PRODUCT OR PART FOUND BY MANUFACTURER TO BE DEFECTIVE IN MATERIAL OR WORK. MANUFACTURER SHALL NOT BE RESPONSIBLE FOR ANY DIRECT, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE OTHER RIGHTS, WHICH MAY VARY FROM STATE TO STATE. HOWEVER, SOME STATES DO NOT ALLOW LIMI- TATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLU- SIONS MAY NOT APPLY TO YOU.
2. Press and release the |
receiver’s PROGRAM button |
once. The receiver’s red |
STATUS LED will turn on and |
remain on for 25 seconds, |
indicating that the receiver is |
ready to learn a transmitter. |
3. Press the button on the |
transmitter you wish to use to |
control the operator. The |
receiver’s red STATUS LED |
will turn on and off three times |
indicating a successful learn. |
4. Press the same button on the |
transmitter once more to confi rm |
operation of the door or gate |
operator. |
5. Test range of transmitter. |
Repositioning antenna may |
provide greater range. |
6. Repeat Transmitter |
Programming steps for |
additional transmitters. |
RED STATUS LED
Operation:
Whenever this receiver senses a valid signal from a learned transmitter, the relay will activate for one second and, therefore, activate the operator.
1.Press and release selected button on Wayne Dalton transmitter.
2.Receiver LED will light and the unit will cycle.
Maintenance:
Disconnect electric power to door or gate operator before making repairs or removing case covers. While this receiver is
Service:
Unit contains no user serviceable parts. Contact your dealer or
To Remove This Receiver From Service:
1.Disconnect power to operator (door operator, gate operator, etc.) and disconnect power to this receiver.
2.Disconnect all wiring connected to receiver. Disconnect antenna and any associated coax wiring.
3.Remove receiver from mounting location. Discard properly per local codes.
4.Reconnect power to operator. Test operator for proper operation.
FCC Regulatory Information:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IC Regulatory Information:Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
NOTE: This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with these instructions, may cause harmful interference to radio communication; however, there is no guarantee that interference will not occur in a particular installa- tion. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning equipment off and on, user is encouraged to try to correct interference by one or more of the following measures:
Reorient or relocate receiving antenna. Increase separation between equipment and receiver. Connect equipment into an outlet on a circuit different from that which receiver is connected. Consult your dealer or/and experienced radio/television technician for help.
WARNING: Changes or modifi cations to this unit not expressly approved by party responsible for compliance could void user’s authority to operate this equipment.
Questions?
STOP
Need Information?
Call Us Toll-Free:
(888)
Thank you for your purchase
www.waynedalton.com
Please Do Not Return This Product To The StoreCall Us Directly! Our Trained Technicians Will Answer Your Questions and /or Ship Any Parts You May Need.
You can reach us Toll Free