Wayne-Dalton 44 Label Placement, Cable Adjustments, Final Adjustments, Residential Dust label

Special knot

3 Hole	Front cable
clip	lift sheave

knot.

23	Label Placement
	Tools: Step Ladder

Counterbalance

lift cable

“S” Hook

Counterbalance	Rear
	cable lift
lift cable	sheave

Horizontal

track angle

Second slot

“S” Hook

Hook plate

Counterbalance

lift cable

IMPORTANT: Using the illustration, attach the appropriate labels to the ap- propriate location on the section, as shown.

NOTE: The Spring Warning tag(s) are factory attached (one per spring).

NOTE: Because of different configurations, some labels may require minor relocations.

Torsion spring tag(s) (one per spring)

HIGH SPRING TENSION CAN CAUSE

SERIOUS INJURY OR DEATH.

Spring safety
cable
Counterbalance	Sheave fork	Horizontal track
lift cable

This illustrations shows doors featuring (2) pairs of extension springs

WARNING

Residential Dust label

(For California Residents Only)

Residential

warning label

WARNING

DO NOT adjust, repair or remove springs or parts to which springs are connected, such as steel brackets, cables, wood blocks, fasteners or other parts of the counterbalance system.

Adjustments or repairs must ONLY be made by a trained door systems technician using proper tools and instructions.

DO NOT remove, cover or paint over this tag. Product user should inspect this tag periodically for legibility and should order a replacement tag from the door manufacturer, as needed.

WARNING

21	Cable Adjustments
	Tools: None

Adjust counterbalance lift cables to create about 1” to 2” (25 mm to 50 mm) of initial exten- sion spring stretch, with the door in the fully opened position.

Measure relaxed extension spring length for your door height and verify with chart. Spring length must be the same for both extension springs to allow even door balance.

Carefully remove the locking pliers from the horizontal track and lower the door into the closed position.

Once the door is closed, measure the extension spring length in tension for both sides. Using the chart, verify the spring length in tension, is correct with your door height.

Note: It may be necessary to adjust spring length for proper door balance.

DOOR HEIGHT	Spring Length Relaxed	Spring Length Extended
	(Door Open)	(Door Closed)
6’0”	25”	61”
	(635 mm)	(1549 mm)
6’3”	25”	62.5”
	(635 mm)	(1588 mm)
6’6”	25”	64”
	(635 mm)	(1626 mm)
7’0”	25”	67”
	(635 mm)	(1702 mm)
7’6”	27”	72”
	(686 mm)	(1829 mm)
7’9”	27”	73.5”
	(686 mm)	(1867 mm)
8’0”	27”	75”
	(686 mm)	(1905 mm)­

22	Final Adjustments
	Tools: None

Now lift the door and check its balance. If the door is hard to pull down or lifts by itself, adjust extension spring length by moving the “S” hook backward (towards the rear back hangs) to a different hole in the horizontal angle.

If the door is difficult to lift or too easy to pull down, adjust extension spring length by moving the “S” hook forward (towards the header) to a different hole in the horizontal angle.

Important: Whenever adjusting extension spring length for door balance, always open the door to the fully open position and return the locking pli- ers to the horizontal tracks below the bottom track rollers.

If the door still does not operate easily, lower the door into the closed position and recheck the following items:

1.) Check the door for level.

2.) Check the distance between flag angles – must be door width plus 3-3/8” + 1/4” – 0”.

3.) Check the counterbalance lift cables for equal tension- adjust by re-tieing the special

Lift handles/gripping points are required			Lift handles/gripping points are required
on this door, located as spelled out in the			on this door, located as spelled out in the
installation instructions, even if the door			installation instructions, even if the door
is motor operated.			is motor operated.
Failure to install and use these lift handles/			Failure to install and use these lift handles/
gripping points on this door can result in			gripping points on this door can result in
serious injury to fingers and/or hands, if			serious injury to fingers and/or hands, if
placed in the opening between sections,		IMPORTANT	placed in the opening between sections,
when the door is operated manually.			when the door is operated manually.
WARNING		THIS WOOD PRODUCT REQUIRES PROPER	WARNING
		ACC0RDANCE TO THE DIRECTIONS GIVEN IN THE
		FINISHING PRIOR TO ANY DOOR HARDWARE BEING
		APPLIED. BOTH INNER AND OUTER FACES OF THE
		SECTION(S), AS WELL AS ALL EDGE SURFACES
	important notice	MUST BE PREPARED AND FINISHED IN STRICT
The adjacent bottom corner bracket and		AND/OR DELAY IN FINISHING, THAT ALLOWS FOR	The adjacent bottom corner bracket and
	Wood label	MANUAL UNDER “MAINTENANCE AND PAINTING
		INSTALLATION INSTRUCTIONS AND OWNER’S
all cable retention features including		INSTRUCTIONS FOR ALL WOOD DOORS”.	all cable retention features including
milford pins, cotter pins, & clevis pins are		IMPROPER STORAGE, IMPROPER TRANSPORTATION	milford pins, cotter pins, & clevis pins are
under HIGH SPRING TENSION.		THE EXPOSURE OF THIS WOOD PRODUCT TO	under HIGH SPRING TENSION.
Adjustments and repairs must only be		THE LIMITED WARRANTY.	Adjustments and repairs must only be
		MOISTURE AND/OR OTHER CONTAMINANTS, VOIDS
made by a trained door systems			made by a trained door systems
technician, using proper tools and			technician, using proper tools and
instructions.			instructions.
DO NOT REMOVE, COVER OR PAINT OVER			DO NOT REMOVE, COVER OR PAINT OVER
THIS LABEL. PRODUCT USER SHOULD			THIS LABEL. PRODUCT USER SHOULD
INSPECT THIS LABEL PERIODICALLY FOR			INSPECT THIS LABEL PERIODICALLY FOR
LEGIBILITY AND SHOULD ORDER A			LEGIBILITY AND SHOULD ORDER A
REPLACEMENT FROM THE DOOR	Bottom section warning labels		REPLACEMENT FROM THE DOOR
MANUFACTURER AS NEEDED.			MANUFACTURER AS NEEDED.

13

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer,

refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com