Wayne-Dalton 6100 Horizontal Tracks/F.A. Flag Angles, TorqueMaster Spring Tube

		Flagangle	1/4”-20 x 9/16”
			Track bolt
Flag angle
Bottom rail
of horizontal	Quick Install
track	tab in place		Washer
Quick
			Top rail of
Install	Tracks flush
			horizontal
tab
	Key slot		track
			1/4”-20
			Flange hex
Vertical	Vertical		nut
track	track

Horizontal Tracks/F.A. Flag Angles

16 Tools: Ratchet wrench, 7/16” Socket, 9/16” Socket, 9/16” Wrench, level, Step ladder, Flat tip screwdriver

Note: If you have Fully Adjustable flag angles, complete this step.

To install horizontal track, place the top rail end over the top track roller of the top section. Align the bottom rail end of the horizontal track with the top of the vertical track. If you have Quick Install horizontal track, tighten the bottom rail of the horizontal track to the flag angle with (1) stud plate and (2) 1/4”-20 flange hex nuts. If you have Universal horizontal track, tighten the bottom rail of the horizontal track to the flag angle with (2) 1/4”-20 x 9/16” track bolts and (2) 1/4”-20 flange hex nuts.

WARNING

Do not raise door until horizontal tracks are secured at rear, as outlined in step, Rear Back Hangs, or door could fall from overhead position causing severe or fatal injury.

Level the horizontal track assembly and bolt the top rail of the horizontal track to the encoun- tered slot in the flag angle using (1) 1/4”-20 x 9/16” track bolt, (1) 1/4”-20 flange hex nut and (1) 5/16 washer. Repeat for other side.

Remove the nail that was temporarily holding the top section in place, installed in step, Top Section.

Important: Failure to remove nail before attempting to raise door could cause permanent damage to top section.

Note: If an idrive® opener will be installed, position horizontal tracks slightly above level.

	Roller
Low headroom	(2) 1/4” - 20
horizontal track	Flange hex nuts
Top bracket
slide	Top section
Top bracket
assembly

		Top bracket slide
(2) 1/4” - 20		(2) Retention washers
Flange hex nuts		Slotted hole of top
		bracket base
Top bracket	Anti-twist	(2) 1/4” - 20 x 5/8”
		Carriage bolts
	feature
slide reversed

18	TorqueMaster® Spring Tube
	Tools: None

TorqueMaster® springs come lubricated and pre-assembled inside the TorqueMaster® spring tube. To prepare for install, lay the spring tube assembly on the floor, inside garage, in front of the door, and with the labeled end to the left.

Bottom rail Quick Install Horizontal track

1/4”-20 Flange hex nuts

Flag angle upper slot

Vertical track

Stud plate

Bottom rail Fully	Flagangle	1/4”-20 x 9/16”
Adjustable		Track bolt
Horizontal
track
1/4”-20
Flange hex		Washer
nuts		Top rail of
		horizontal
Flag angle		track
upper slot		1/4”-20
Vertical		Flange hex
track		nut
1/4”-20 x 9/16” Track bolts

TorqueMaster® spring tube

Label

19	Center Bracket Bushing Assembly
	Tools: None

17	Adjusting Top Fixtures
	Tools: 7/16” Wrench, Step ladder

With horizontal tracks installed, you can now adjust the LHR top brackets.

NOTE: Depending on your application, you may need to reverse the top bracket slide for more adjustment, if needed, prior to securing it to the top bracket base.

To adjust the top bracket slides: Loosen the (2) 1/4”-20 flange hex nuts (if neces- sary) and vertically align the top section of the door with the lower sections. Once aligned, position the top bracket slide, out against the horizontal track. Maintaining the slide’s posi- tion, tighten the (2) 1/4”-20 flange hex nuts to secure the top bracket slide to the top bracket base. Repeat for other side.

To reverse the top bracket slides (if needed): Remove the two 1/4” - 20 x 5/8” carriage bolts, two retention washers and two 1/4” - 20 flanged hex nuts. Flip the top bracket slide in the opposite direction. Loosely fasten the top bracket slide to the bracket using two 1/4” - 20 x 5/8” carriage bolts, two retention washers and two 1/4” - 20 flanged hex nuts, as shown.

NOTE: The retention washers must be fully seated against the top bracket base to ensure the anti-twist feature on the top bracket slide engages in the slotted hole in the top bracket base.

Note: If you are installing the idrive® opener with your garage door, skip this step and go to your idrive® Installation Instructions and Owner’s Manual. After completing the steps up to and including, Drum Wrap Installation of your idrive® Installation Instructions and Owner’s Manual continue with Step, Rear Back Hangs, of this door Installation Instructions and Owner’s Manual.

Note: If you are not installing the idrive® opener on your garage door, you must install the center bracket bushing assembly. Follow these instructions for non-idrive®operated garage doors.

Being cam shaped, the center bushing only fits one way. Slide the center bracket bushing as- sembly towards the center of the TorqueMaster® spring tube, from the right side, as shown.

Center bracket

TorqueMaster® spring tube

Center bushing Cam peak

Center bracket bushing assembly

10

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer,

refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com