Operating Instructions and Parts Manual |
|
|
| Deep Well Submersible Pump | |||||||
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| Cable Size |
|
|
|
| |
|
| 14 | 12 | 10 | 8 | 6 | 4 | 3 | 2 | 1 | 0 |
Volts | HP | (2 mm2) | (3 mm2) | (5 mm2) | (7 mm2) | (13 mm2) | (21 mm2) | (25 mm2) | (34 mm2) | (41 mm2) | (50 mm2) |
| 1/2 | 400 | 650 | 1020 | 1610 | 2510 | 3880 | 4810 | 5880 | 7170 | 8720 |
|
| (121.9) | (198.1) | (310.9) | (490.7) | (765) | (1182.6) | (1466.1) | (1792.2) | (2185.4) | (2657.9) |
230 | 3/4 | 300 | 480 | 760 | 1200 | 1870 | 2890 | 3580 | 4370 | 5330 | 6470 |
|
| (91.4) | (146.3) | (231.6) | (365.8) | (570) | (880.9) | (1091.2) | (1332) | (1624.6) | (1972.1) |
| 1 | 250 | 400 | 630 | 990 | 1540 | 2380 | 2960 | 3610 | 4410 | 5360 |
|
| (76.2) | (121.9) | (192) | (301.8) | (469.4) | (725.4) | (902.2) | (1100.3) | (1344.2) | (1633.7) |
NOTE: Specified maximum wire lengths are valid with motor voltage greater than or equal to 95% of service entrance voltage and motor running at maximum nameplate amperes. If service entrance voltage is at least motor nameplate voltage under normal load conditions, 50% additional length is permissible for all sizes shown.
Table 3 - Power supply wire (cable) length in feet (m)
1 phase, 2 or 3 wire cable, 60 Hz (copper wire
Electrical System
(Continued)
use only control box specified
for your pump. Make sure motor and control box match (see Table 4, on page 3). Failure to do so will void warranty.
4.Install circuit protection and component protection in compliance National Electrical Code, Part 1. Consult with appropriate code officials for more information on how to do this.
|
|
| Pump Model | Control Box |
HP | Voltage | Wires | No. | No. |
1/2 | 230 | 3 | ||
1/2 | 230 | 2 | None | |
1/2 | 115 | 2 | None | |
3/4 | 230 | 3 | ||
3/4 | 230 | 2 | None | |
1 | 230 | 3 |
Table 4 - Control box chart
If main overload trips, look for the |
|
|
|
|
|
|
|
|
|
following: | 115V or | GROUND |
|
| TO LINE | GROUND |
| ||
1. Shorted capacitor | 230V LINE |
|
|
|
|
|
| ||
| FUSED |
|
|
|
|
|
| ||
2. Voltage problems |
|
|
|
|
|
|
| ||
| DISCONNECT |
|
|
|
|
| |||
3. Overloaded or locked pump. |
| SWITCH |
| CONTROL |
|
|
|
| |
|
|
|
| BOX |
|
|
|
| |
Single Phase, 2 Wire |
| L1 | M1 |
| L1L2R Y B |
| L1 | M1 |
|
|
|
|
|
| |||||
| L2 M2 |
|
|
| L2 | M2 |
| ||
wires and one ground wire (Green). A |
|
|
|
|
| ||||
|
|
| PRESSURE |
|
|
|
| ||
control box is not required. See Figure |
|
|
| FUSED |
|
|
| ||
1b for correct hookup for 230 volt |
| RED | SWITCH | DISCONNECT |
|
| |||
|
|
| SWITCH |
| PRESSURE |
| |||
|
| YELLOW |
|
|
|
| |||
|
|
|
|
| SWITCH |
| |||
| BLACK |
|
|
|
|
| |||
|
|
|
|
| RED |
| |||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| BLACK |
| |
|
|
| WELL | GROUND |
|
|
|
| |
|
|
|
|
|
|
| GROUND | ||
|
|
| CASING |
|
|
|
| ||
|
|
|
|
|
|
|
| WELL | (GREEN) |
|
| Follow color coding when |
|
| CASING |
| |||
|
|
|
|
|
| ||||
|
| connecting control box wires. |
|
|
|
| |||
|
| (Yellow = Y, Red = R, Black = B) |
|
|
|
| |||
| Figure 1a - 3 wire, | Figure 1b - Single phase, 2 wire | |||||||
| disconnect box |
|
|
| connections |
|
| ||
|
|
|
|
|
|
|
| www.waynepumps.com | |
|
|
| 3 |
|
|
|
|
|
|
