Weber 56204 manual Sear Station Troubleshooting, Rotisserie Troubleshooting

SEAR STATION® TROUBLESHOOTING

PROBLEM	CHECK	SOLUTION
Burners burn with a yellow or	Inspect Spider/Insect Screens for possible obstructions.. (Blockage	Clean Spider/Insect Screens..
orange flame, in conjunction with	of holes..)	(See “ANNUAL MAINTENANCE” section)
the smell of gas (This is normal for
	Did you ignite the two adjacent main burners? (See “SEAR	Verify adjacent main burner ignition by visual inspection of a flame.
the burner lighting tube).
	STATION® IGNITION & USAGE” instructions for safe lighting
Sear Station® burner does not light.		m WARNING: If ignition does not occur in 5
	procedure)
		seconds, turn burner control OFF, wait 5
		minutes to let the gas clear before you try
		again.
	Does Burner light with a match?	If you can light Burner with a match, then check the Crossover®
		Channel on the sear burner..
		(See “MAINTENANCE” for burner removal and cleaning
		procedure..)
	Does the igniter work (Do you see a spark when you repeatedly	Try manually lighting the burner (refer to “SEAR STATION®
	use the snap igniter?	IGNITION & USAGE”).. Call customer service..
General Symptoms:	The excess flow safety device, which is part of the barbecue to	To reset the excess flow safety device turn all burner control knobs
Burner does not light. -or-	cylinder connection, may have activated..	and the cylinder valve to OFF.. Disconnect the regulator from the
		cylinder.. Turn burner control knobs to START/HI.. Wait at least 1
Burner has a small flickering flame.
		minute.. Turn burner control knobs to OFF.. Reconnect the regulator
		to the cylinder.. Turn cylinder valve on slowly.. Refer to “MAIN
		BURNER IGNITION”..

If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our web site. Log onto www.weber.com®.

ROTISSERIE TROUBLESHOOTING

PROBLEM	CHECK	SOLUTION
Rotisserie burner does not light.	Did you hold the burner control knob in and hold in for 20 seconds	Try to relight burner by holding burner control knob in and continue
	until after burner ignited?	holding in until 20 seconds after burner has ignited..
	Did you wait to see the entire ceramic surface become alight	When relighting burner by holding burner control knob in, wait to
	before counting 20 seconds?	see the entire ceramic surface become alight before counting 20
		seconds?
	Did you repeatedly use the snap ignition until the burner ignited?	After waiting five minutes for gas to clear, try repeatedly using
		the snap igniter until the burner ignites (refer to “ROTISSERIE
		BURNER IGNITION & USAGE”)..
	Does the igniter work (Do you see a spark when you repeatedly	Try manually lighting the burner (refer to “ROTISSERIE BURNER
	use the snap igniter)?	MANUAL IGNITION”).. Call customer service..
General Symptoms:	The excess flow safety device, which is part of the barbecue to	To reset the excess flow safety device turn all burner control knobs
Burner does not light. -or- Burner	cylinder connection, may have activated..	and the cylinder valve to OFF.. Disconnect the regulator from the
		cylinder.. Turn burner control knobs to START/HI.. Wait at least 1
has a small flickering flame.
		minute.. Turn burner control knobs to OFF.. Reconnect the regulator
		to the cylinder.. Turn cylinder valve on slowly.. Refer to “MAIN
		BURNER IGNITION”..

If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our web site. Log onto www.weber.com®.

GRILL OUT™ HANDLE LIGHT TROUBLESHOOTING

PROBLEM	CHECK	SOLUTION
Weber Grill Out™ Handle Light	Are the batteries old?	Replace batteries..
does not light.
	Are the batteries installed correctly?	Refer to assembly illustration..
	Is the lid in the up position with the power button ON?	Light will activate when lid is open..
	Is the Weber Grill Out™ Handle Light activated?	Press the power button..
	Is the Weber Grill Out™ Handle Light positioned correctly on the	Adjust position (refer to assembly illustration).
	handle?

If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our web site. Log onto www.weber.com®.

32