HOW to Stop Your Unit

IMPORTANT

Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during stor- age. Acidic gas can damage the fuel system of an engine while in storage.

To avoid engine problems, empty the fuel sys- tem before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season.

Never use engine or carburetor cleaner prod- ucts in the fuel tank or permanent damage may occur. See the STORAGE section for addi- tional information.

S To stop the engine, push and release the engine ON/STOP switch. The switch will automatically return to the ON position. Wait 5 seconds before attempting to restart unit to allow switch to reset.

SIf engine does not stop, move choke to the FULL CHOKE position.

Engine

Choke Lever

ON/STOP

Switch

FULL HALF OFF

HOW TO START YOUR UNIT

WARNING: The trimmer head will turn while starting the engine. Avoid any con- tact with the muffler. A hot muffler can cause serious burns.

STARTING A COLD ENGINE (or a warm engine after running out of fuel)

Starting Position

1.Set unit on a flat surface.

2.Slowly press the primer bulb 6 times.

3.Move choke lever to the FULL CHOKE position.

4.Squeeze the throttle trigger fully and hold through all remaining steps.

Starter Handle

Choke

Lever

Muffler

Primer Bulb

5.Pull starter rope handle sharply until engine sounds as if it is trying to start, but do not pull rope more than 6 times.

6.As soon as engine sounds as if it is trying to start, move choke lever to HALF CHOKE position.

7.Pull starter rope sharply until engine runs, but no more than 6 pulls.

NOTE: If the engine doesn’t start after 6 pulls (at the HALF CHOKE position), move the choke lever to the FULL CHOKE position and press the primer bulb 6 times. Squeeze and hold the throttle trigger and pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE position and pull the start- er rope until the engine runs, but no more than 6 pulls. If the engine still doesn’t start, it is probably flooded. Proceed to

STARTING A FLOODED ENGINE.

8.Once the engine starts, allow it to run 10 seconds, then move the choke lever to the OFF CHOKE position. Allow the unit to run for 30 more seconds at OFF CHOKE before releasing the throttle trig- ger.

NOTE: If engine dies with the choke le- ver in the OFF CHOKE position, move the choke lever to the HALF CHOKE position and pull the rope until engine runs, but no more than 6 pulls.

STARTING A WARM ENGINE

1.Move the choke lever to the HALF CHOKE position.

2.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until the en- gine runs smoothly.

3.Pull starter rope sharply until engine runs, but no more than 5 pulls.

4.Allow engine to run 15 seconds, then move the choke lever to OFF CHOKE.

NOTE: If engine has not started, pull starter rope 5 more pulls. If engine still does not run, it is probably flooded.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the choke lever in the OFF CHOKE position; then, pull the rope to clear the engine of ex- cess fuel. This could require pulling the starter handle many times depending on how badly the unit is flooded.

If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

530086930 specifications

The Weed Eater 530086930 is a powerful and reliable tool designed for homeowners and landscaping professionals seeking efficiency in lawn maintenance. This product stands out in the realm of string trimmers, offering features that cater to both ease of use and performance.

One of the main features of the Weed Eater 530086930 is its lightweight design, making it easy for users to maneuver while trimming hard-to-reach areas. Weighing just around 10 lbs, this trimmer reduces fatigue, allowing users to work for extended periods without discomfort. The adjustable handle further enhances its ergonomic design, accommodating various user heights and preferences.

The Weed Eater 530086930 utilizes a gas-powered engine that delivers robust performance, ensuring that tough weeds and grass are tackled with ease. This trimmer is equipped with a 2-cycle engine, which is known for its reliability and power output. The engine is designed for efficient fuel consumption, enabling longer operation times between refuels, thus increasing productivity in yard care tasks.

A standout feature of the Weed Eater 530086930 is its automatic line advance system. This technology ensures that the cutting line is fed seamlessly, preventing downtime caused by line adjustments. The system is both user-friendly and efficient, allowing for uninterrupted trimming.

Another significant characteristic is the versatile cutting ability. The Weed Eater 530086930 can effectively transition between trimming and edging tasks. It features a pivoting head that rotates easily, allowing users to switch angles seamlessly for different tasks. This versatility makes it an ideal choice for maintaining borders, flower beds, and tight corners.

Durability is also at the forefront of the Weed Eater 530086930's design. The trimmer is constructed with rugged materials that can withstand the demands of regular use, ensuring longevity. Additionally, the replacement parts are readily available, making maintenance and repairs straightforward.

In summary, the Weed Eater 530086930 combines lightweight design, powerful engine performance, user-friendly technologies, and durability. These characteristics make it a valuable tool in any lawn care regimen, appealing to both casual users and serious landscaping enthusiasts. Whether you are trimming overgrown areas or maintaining neat edges, the Weed Eater 530086930 is engineered to deliver reliable, efficient, and effective results.

Weed Eater 530086930 HOW to Stop Your Unit, HOW to Start Your Unit, Starting a Warm Engine

Models: 530086930