Weed Eater WE261 warranty Check Tire Pressure, Check Deck Levelness, Check Brake System

4.Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

Flat Washer

02464

Adjustment Knob

5.Lower seat into operating position and sit in seat.

6.Slide seat until a comfortable position is reached which allows you to press clutch/ brake pedal all the way down.

7.Get off seat without moving its adjusted position.

8.Raise seat and tighten adjustment knob securely.

CHECK BATTERY

Make sure battery is securely fastened, and that all wires are securely connected.

•Battery is located under the seat.

•Battery has been fully charged from the factory, before installation.

Seat

Battery

NOTE: You may now roll your riding mower off the skid. Follow the appropriate instruction below to remove the riding mower from the skid.

WARNING: Before starting, read, un- derstand and follow all instructions in the Operation section of this manual. Be sure riding mower is in a well-ventilated area. Be sure the area in front of riding mower is clear of other people and objects.

TO ROLL RIDING MOWER OFF SKID (See Operation section for location and function of controls)

1.Raise deck lift lever to its highest position.

2.Release parking brake by depressing clutch/brake pedal.

3.Engage freewheel control. See “TO TRANSPORT” in the operation section of this manual.

4.Roll riding mower forward off skid.

CHECK TIRE PRESSURE

The tires on your riding mower were overinflated at the factory for shipping pur- poses. Correct tire pressure is important for best cutting performance.

•Reduce tire pressure to PSI shown on tires.

CHECK DECK LEVELNESS

For best cutting results, mower housing should be properly leveled. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

CHECK FOR PROPER POSITON OF MOWER DRIVE BELT

See the figure that is shown for replacing the mower drive belt in the service and adjustment section of this manual. Verify that the belt is routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your rid- ing mower, check to see that the brake is operating properly. See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual.

RIDING MOWER - -CATALOG NO. WE261

DRIVE

KEY	PART		KEY	PART
NO.	NO.	DESCRIPTION	NO.	NO.	DESCRIPTION
– –	532 43 61-44	SERVICE KIT, TRANSAXLE	41	819 09 12-10	WASHER FLAT
1	532 43 64-98	WHEEL ASM (REAR)	42	532 16 60-02 WASHER, SERRATED
2	532 12 17-48	WASHER, 16 GA.	43	873 68 04-00 NUT, CROWN LOCK 114-20
3	812 00 00-01	E-CLIP	45	817 49 04-36 SCREW 1/4-20 X 2 114
4	532 12 35-83	KEY. SQUARE	46	819 09 10-16	WASHER
5	532 42 79-39	WELDMENT. DRIVE AXLE	47	817 49 04-20 SCREW, 1/4-20 X 1 1/2
6	532 42 80-69	CHAIN DRIVE	48	532 43 02-49	PLATE BRAKE ANTI - ROTATE
7	532 42 78-73	SPROCKET. 9 TOOTH	49	532 43 02-45 SPRING, BRAKE RETURN
		SPLINED	50	532 42 80-21	ARM, BRAKE
8	812 10 00-09	RING, SNAP	51	532 43 02-47 SPACER RETURN
10	532 42 88-76	DIFFERENTIAL ASM	52	532 42 80-78 CALIPER, BRAKE ASM
11	532 00 13-70	WASHER, THRUST	53	877 01 08-10 PIN, DOWEL 1/4
12	532 43 06-45	CHAIN, PRIMARY DRIVE	54	532 42 80-19 PLATE, BRAKE PAD
13	532 43 08-45	BUSHING	55	532 42 80-17	PUCK BRAKE
14	532 43 85-68	BRACKET, CARRIER	56	532 43 52-53 ROTOR, BRAKE
15	532 12 47-93	BEARING ASM	57	532 42 80-16 CAP, BRAKE CALIPER
16	532 42 79-26	SHAFT INPUT	58	532 12 47-88	PIN, RETAINER
17	532 43 72-81	WHEEL, FRICTION A5M	59	817 49 05-08 BOLT, 5/16-16 X 112
18	532 42 47-59	ARM, SHIFT	60	532 44 08-55	CABLE, BRAKE
19	532 43 08-70	ROD, BYPASS	61	532 42 79-45 WELDMENT, PEDAL
20	532 42 79-97	BRACE CARRIER REAR	62	532 42 96-78 ROD, PARKING BRAKE
21	532 42 80-77	SPRING, CARRIER	63	877 10 08-12 PIN, .25 X .75 CLEVIS
22	532 42 80-76	SPRING, BRAKE	64	532 42 10-76 PIN, COTTER 5/64 X 3/4
23	532 43 13-74	SPRING, BYPASS	65	532 42 93-25 BRACKET, BRAKE SUPPORT
24	532 42 79-95	BRACE CARRIER BOX	66	532 42 96-94	COVER PEDAL
25	532 42 83-03	LINK, SHIFT	67	532 42 96-93 COVER, BRAKE PEDAL
26	532 42 98-16	ARM. CLUTCH	68	817 06 05-16 SCREW, 1/4-20 X 3/8
27	532 42 90-53	WELDMENT SHIFT LEVER	69	532 42 80-70 BRAKE CABLE MOUNT
28	532 42 83-02	SUPPORT, SHIFT LEVER	70	817 00 05-12 BOLT, 5/16-18 X 3/4
29	532 17 48-40	WASHER, NYLON	71	532 43 64-99	CAP HUB AXLE
30	532 18 39-00	HUB SHIFT LEVER	73	532 42 95-19 SPROCKET II TOOTH
31	532 42 90-55	SPACER, NYLON			SPLINED
32	532 42 84-64	MNTG BRKT. SHIFT ARM	74	532 43 78-41 TENSION LRV CHAIN
33	532 42 84-61	BRACKET, SHIFTER FLEX	75	532 43 34-95 SPROCKET IDLER
34	532 42 84-62	TUBE SHIFT ARM	117	812 00 00-40 RING KLIP #T5304-62
35	532 41 15-55	GRIP, HANDLE
36	872 11 04-06	BOLT, CARRIAGE - 114-20 X 3/4
37	873 80 04-00	NUT NYLON LOCK 114-20
38	532 16 54-92	BOLT, SHOULDER	NOTE: All component dimensions given in U.S. inches
39	874 78 04-12	BOLT, 1/4-20 X 3/4
40	810 04 04-00	WASHER, LOCK		1 inch = 25.4 mm

8 33